GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. |
|
The high-speed roller feeder is the most cost-effective, energy-efficient and low-failure
feeding device among the five commonly used feeders in the stamping
industry. Therefore, it has become the preferred punch feeder for
current stamping customers.
The six high-speed roller feeders use the following precautions:
1. The actual maximum feeding material width of the high-speed
roller feeder is not the specification indicated on the model, but
should be reduced by 10mm in the actual specification.
2. The continuous stamping feeding step of the high-speed roller
feeder should be adjusted to be slightly larger than the inching
test mode.
3. After the punching machine is replaced with the mold, the
feeding height of the roller feeder should be adjusted accordingly
to ensure that it is at the same level as the material line height
of the actual matching mold.
4. After the stamping process changes and adjusts the step of the roller feeder, the position of the rocker arm and the tie rod needs to be
adjusted.
5. In the process of using the stamping automatic production line,
when it is necessary to stop the machine, it is necessary to stop
the punching machine and then stop the sequence of the flattening
machine. Avoid insufficient feeding due to premature shutdown of
the leveling machine, causing the punch to mis-shoot and damage the
mold.
6. When the high-speed roller feeder is in use, if there is any
problem such as inaccurate feeding, material feeding, and
looseness, it is necessary to stop immediately for maintenance,
find out the problem, and completely eradicate before restarting
production.
Specification:
Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
Power(V) | 3 Phase 220V/380V/50HZ | |||||
Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 |
Straigtening performance:
tock Thicknees (mm) | Stock Width (mm) | |||
0.3 | 400 | 500 | 600 | 800 |
0.4 | ||||
0.6 | ||||
0.8 | ||||
1.0 | ||||
1.2 | ||||
1.4 | ||||
1.6 | 470 | 470 | ||
1.8 | 400 | 400 | ||
2.0 | 360 | 360 | ||
2.3 | 300 | 300 | 300 | 300 |
2.5 | 230 | 230 | 230 | 230 |
2.8 | 150 | 150 | 150 | 150 |
3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is
provi