Active Member
|
[China]
Address: No. 12, Chuangxing Road, Baisha, Humen Town, Dongguan, Guangdong, China
Contact name:Calin Deng
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. |
|
|
1.NC servo feeder: This is a punching machine with the highest
degree of automation, the widest range of use, the best feeding
accuracy and the easiest operation. It can feed the air feeder up
to 10m. The wide material and thick material that can not be
transported by the roller feeder can be input on the touch screen
by the setting of the feed step, speed and frequency. However,
since the electronic control system.
2. roller feeder: This is currently the most used feeder with the punching machine, its price is higher than the air feeder but lower than the NC
servo feeder, is the most cost-effective model of these three punch
feeder, it itself Without power, it is powered by an eccentric disk
mounted on the output shaft of the punching machine. The feeding
step is adjusted by the eccentricity of the eccentric disk.
Therefore, the feeding step is limited to a maximum of 300 mm, and
the matching punch must be There is an output shaft.
3. Air feeder: This is the earliest feeding equipment used in the
stamping industry to realize automatic production with the use of
punching machine. It is powered by external air source (8C and 8C
air feeder with its own cylinder), through the cylinder clamp Tight
material, the floating rod is pressed down by the floating rod to
realize the feeding, and the feeding step and time are adjusted by
the degree of the floating rod pressing the cylinder. The air
feeder has the lowest price among the three punch feeders. If the
precision of the stamping product is not high, the punch feeder
model can be considered, but pay special attention to the air
feeder failure rate is relatively high, in actual use. Need to be
maintained.
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is
provi
