HEBEI QINYI CONVEYING EQUIPMENT CO.,LTD |
|
Belt Conveyor Impact Idler And Return Roller With Rubber
the impact idler is used at the receiving place of the belt conveyor to slow down the impact of the blanking on the conveyor belt. It is a type of idler mainly developed for corrosive environments such as coal washing plants, coking plants, and chemical plants. , Its toughness is more than 10 times that of ordinary metals, its life is five times that of traditional column shoes, corrosion resistance, flame retardant, antistatic, light weight and other characteristics, it is widely used in mining. The polymer material specially used for the roller body, its mechanical properties are similar to bronze, it has good wear resistance, and it has good self-lubricating properties, which does not damage the belt. The buffer idler has excellent anti-corrosion performance. The roller body and seals are made of polymer materials, which are corrosion-resistant. Used in corrosive occasions, the service life can reach more than 5 times that of ordinary idlers.
The buffer idler is light in weight and has small rotational
inertia. The special polymer material for idlers is light in
weight, and its specific gravity is one-seventh of that of steel.
The idler made of this material is about one-half of the weight of
ordinary idlers, and the rotational inertia is small, and the gap
between the idler and the belt is small. friction is small.
use action
1. Before using the idler, carefully check the appearance for
serious bump damage. The rotating idler should rotate flexibly
without jamming.
2. The installation distance of the idler should be determined by
scientific calculation according to the type of logistics and the
characteristics of the conveyor, so as to avoid too sparse or too
dense installation.
3. The installation of idlers should be adapted to avoid friction
with each other.
Product name | Belt Conveyor roller |
Lift time | 50000 hours |
Production capacity | As usual 600 pieces/day |
Diameter & Length | Dia: 76-219mm, Len: 190-3500mm |
Tube | Q235 carbon steel |
Shaft | 45# Cold drawing round steel, Dia: 20mm, 30mm , 35mm, 40mm |
Bearing | Single and double row deep groove ball bearing 2RZ and 2Z with C3
clearance |
Bearing No. | 6204, 6205, 6305, 6306, 6307, 6308, 6309, 6310 |
Seals | Grease retaining inner seal with multi-stage labyrinth and
retention cap with outboard rubbing flinger seal |
Welding | Mixed gas shielded arc welding end |
Finish | Painting/rubber/steel screw/galvanized |
Standard | ISO/BS/JIS/DIN/CEMA/Australia |
Material feature | Water, wear, dust and corrosion resistance |
Certifications | ISO9001/BV/SGS |
Application | Harbor & port, coal, mining, quarry, power industry, cement
plant etc |
The role of the idler is to support the weight of the conveyor belt
and the material. After the type and model of the tapered idler and
friction idler are determined, the combined structure design of the
rolling tapered idler and friction idler is required to be
accurate. The normal operation of the tapered roller and friction
roller. The combined structure design of tapered roller and
friction roller includes
The role of the roller is to reduce the friction between the
conveyor belt and the roller, which accounts for more than 25% of
the total cost of the conveyor and plays a key role in the life of
the conveyor belt. Although the roller is a small part in the belt
conveyor, the structure is not complicated, but it is not easy to
make a good quality roller. The trough roller set is an important
part of the belt conveyor, with many types and large quantities. It
accounts for 35% of the total cost of a belt conveyor and bears
more than 70% of the resistance. Therefore, the quality of the
roller is particularly important. The radial runout of the roller
affects the belt conveyor. Within the range of runout specified in
our country, the belt conveyor can be kept running smoothly,
otherwise it will cause the belt conveyor belt to resonate and
jump, causing material toss and polluting the environment. The
higher the belt speed, the more it appears that the radial runout
is small.
1. Lubrication and sealing of tapered rollers and friction rollers
2. Coordination of tapered roller, friction roller and related
parts;
3. Shafting support end structure
4. Improve the rigidity of the tapered roller and friction roller
system.