Active Member
|
[China]
Address: 1ST FLOOR, UNIT 1, NO.9 GUANSHAN ROAD, FENGDU INDUSTRIAL PARK, PINGYAO, YUHANG, HANGZHOU, ZHEJIANG
Contact name:Colin Mao
ZHEJIANG XINCHOR TECHNOLOGY CO., LTD. |
|
|
Side by Side Cartridge Chemcial Anchor Adhesive For Thread Rods
Chemical anchor adhesive, epoxy injection mortar, Chemical fixing
glue,
Chemical anchoring system used for anchoring and rebar connections
in concrete.
Item #: FixingChor142
Capacity: 420ml
Materials: Epoxy
Mixing Ratio: 1:1
Product Description:
Side by Side Cartridge Chemcial Anchor Adhesive For Thread Rods is
a high performance, two components pure epoxy resin system. strong fixing with exceptionally
high chemcial resistance.Applied in one single action this resin will produce a high performance,
PRODUCT FEATURES
- High grip force, high adhesive force.
- Longer working time.
- Styrene free.
- Designed for use with threaded rod and reinforcing bar hardware elements.
- Special application to diamond drilled holes and large bore diameter.
- The product ingredient is odorless and non-toxic.
- Orange color can be easily detected or monitored.
- Wide temperature range(5°C~+40°c)
Application Range
Fixing of the following substrates:
Concrete
Hard natural and reconstituted stone
Solid rock and masonry
Metal Work, carpentry
Fixing of handrails, balustrades and supports
Fixing of railings
Mechanical and electrical services installation
Anchoring of supports for ducting and equipment.
For structural work:
Bolts and special fastening systems
Rebar / steel reinforcement anchoring in new and refurbishment works.
Threaded rods
Testing project | Condition | Index | ||
Gel Performance (According to China National Standard GB50728-2011) | ||||
Splitting Tensile Strength (MPa) | Under (23±2)℃,(50±5)%RH, tested by loading speed of 2mm/min | ≥8.5 | ||
Flexural Strength (MPa) | ≥50 (no fragment damage) | |||
Compressive Strength (MPa) | ≥60 | |||
Bonding Capacity (According to China National Standard GB50728-2011) | ||||
Steel-Steel Tensile Shear Strength (MPa) | (23±2)℃,(50±5)%RH | ≥10 | ||
Bonding strength of Ribbed steel bar (or screw) with concrete under constrain drawing condition | (23±2)℃ (50±5)%RH | C30,Ф25,L=150mm | ≥11 | |
C60,Ф25,L=150mm | ≥17 | |||
Steel-Steel T-peeling strength (mm) | (23±2)℃,(50±5)%RH | ≤25 | ||
Non-volatile content | (105±2)℃,(180±5)min | ≥99% | ||
Ageing resistance to heat and humidity 90d | ||||
Reduction rate of tensile strength | Under normal room temperature | ≤12% | ||
(According to China National Standard JGJ145-2013) | ||||
Tensile Strength (after high temperature welding) | Dia12 Grade II steel, C30 concrete Hole dia.16mm, Depth: 150mm | 55.1N, 57.0N, 54.8N | ||
Approved for anchorings in:
Concrete, cracked and non-cracked Applications
Rebar planting in concrete structures.
Railway or express way modification works
Structure reinforcement
Curtain wall installing
Bridge modification works
Keel fixing in out wall
ATTENTION
-If the cartridge is not finished, please clean the opening, then put the plug back and cap tightly.
-At temperatures below 10°C should be warmed or stored in temperatures
of 10-30°C for 24hours prior to use to improve product flow and cure.
-If the gelling time expires, please use a new static mixer.
-Do not cut or shorten nozzles.
-It can be used again in the future by replacing the static mixer.
-Please ensure hole is properly cleaned. Hole may be damp but must be free from water.
-Do not install anchors when substrate temperature is less than 0°C.
-Do not install anchors when the temperature is less than 10°C.
