Changzhou Xinpeng Tools Manufacturing Co.,Ltd |
Verified Suppliers
|
|
High Speed Ball Mill Cutter For Steel Good Heat Resistance
The ball nose end mill has four flutes for machining on hardened
and high-alloy steel, steel casting, chill casting, malleable cast
iron, chromium-nickel steel, brass, copper, aluminum with a high
percentage of silicon, and abrasive plastic. Four flutes produce a
better finish than fewer flutes. The tool’s ball nose creates
contoured surfaces where sharp corners are not required. It
balances lower angles’ strong cutting edge for difficult-to-machine
materials with higher angles’ increased cutting action. The
center-cutting design has cutting teeth at the end of the tool, so
it can be fed into the workpiece like a drill bit.
Specifications
HG680 high speed and high hardness milling cutter series is made of
high-quality European grain tungsten steel material, with bending
strength of 4600mpa and grain size of 0.2 μm, which is coated with
imported Balzers high-performance composite coating. HG680 milling
cutters are with special groove design, are especially suitable for
high hard material processing. The service life of cutting tools
can meet the requirements of great brands. With high precision
quality control, and full inspection, all HG680 series end mills
are delivered with 100% qualification rate.
Raw Material | K44 |
WC | 88% |
Co | 12% |
TRS | >4600N/mm2 |
Hardness | >94HRA |
A.O.L | 50mm-150mm |
Grain size | 0.2μm |
Upto | <HRC65 |
Flutes No | 4F |
Coating | Balzers |
Suitable for | Steel,stainless steel,nickel alloy,Titanuim alloy,cast iron,plastic and other materials |
Standard Sizes
Size | Flute Length of End Mills(mm) | |
Flat end | Ball Nose | |
D1*D4*50 | 3 | 2 |
D1.5*D4*50 | 4 | 3 |
D2*D4*50 | 5 | 4 |
D2.5*D4*50 | 6 | 5 |
D3*D4*50 | 8 | 6 |
D3*D3*50 | 8 | 6 |
D3.5*D4*50 | 9 | 7 |
D4*D4*50 | 10 | 8 |
D1*D6*50 | 3 | 2 |
D1.5*D6*50 | 4 | 3 |
D2*D6*50 | 5 | 4 |
D2.5*D6*50 | 6 | 5 |
D3*D6*50 | 8 | 6 |
D3.5*D6*50 | 9 | 7 |
D4*D6*50 | 10 | 8 |
D6*D6*50 | 13 | 10 |
D6*D6*50 | 15 | 12 |
D7*D8*60 | 17 | 14 |
D8*D8*60 | 20 | 16 |
D10*75 | 25 | 20 |
D12*75 | 30 | 24 |
D14*100 | 45 | 28 |
D16*100 | 45 | 32 |
D18*100 | 45 | 36 |
D20*100 | 45 | 40 |
Flute Length of Extended End Mills(mm) | ||
D3*D4*75 | 12 | 6 |
D4*D4*75 | 16 | 8 |
D5*D6*75 | 18 | 10 |
D6*D6*75 | 25 | 12 |
D8*75 | 30 | 16 |
D3*D4*100 | 15 | 6 |
D4*D4*100 | 20 | 8 |
D5*D6*100 | 30 | 10 |
D6*D6*100 | 30 | 12 |
D8*D8*100 | 35 | 16 |
D10*100 | 40 | 20 |
D12*100 | 45 | 24 |
D6*D6*150 | 40 | 12 |
D8*D8*150 | 50 | 16 |
D10*150 | 55 | 20 |
D12*150 | 55 | 24 |
D14*150 | 60 | 28 |
D16*150 | 70 | 32 |
D18*150 | 70 | 70 |
D20*150 | 70 | 70 |