Home Companies Shenzhen Bwin Precision Tools Co., Ltd.

Good Rigidity Carbide End Mill CVD Coated Corner Rounding End Mill

Active Member

Contact Us

[China]

Address: No.1613, honghai Bldg., Songgang Rd., Baoan Area ,Shenzhen , China

Contact name:Judy Le

Shenzhen Bwin Precision Tools Co., Ltd.

Good Rigidity Carbide End Mill CVD Coated Corner Rounding End Mill

Country/Region	china
City & Province	shenzhen

Product Details

Cnc Carbide End Mill 2F Flat Endmill HRC45 Milling Cutter CVD Coated 1.5mm 6mm

Characteristic:

zero point four μ M Extremely fine particles
Newly upgraded Balchas coating
Large core diameter design and tempering treatment
Double edge belt design enhances cutting rigidity
The 45 ° spiral angle shall be cut smoothly without chip accumulation

Description:

The imported micro particle tungsten steel base material is adopted, and the carbide round nose knife has higher wear resistance and strength, which extends the service life of the tool; The newly upgraded Balchas coating can directly perform rough machining to fine machining of heat treated materials below 45 °, reduce tool change times and improve processing efficiency; Imported passivation equipment, spray type to enhance the corrosion resistance and wear resistance of the tool, so that the cutting edge is free of burrs and the cutting is smooth; Double edge band design enhances the rigidity of cutting edge and effectively removes burrs; 45 ° spiral angle, smooth cutting without chip accumulation; Large core diameter design enhances rigidity and seismic resistance.

Milling parameters:

HRC45 Carbide End Mill				Tool length		fz&v
				Short		1
				Long1		0.9
				Overlength		0.8
				Speciality		0.6
Type			Material	Strength N/mm² Hardness HRC	Cooling
					Air	Dry cutting	Lubricating fluid
P	PI	P1.1	Non alloy structural steel, free cutting structural steel, carburized steel and quenched and tempered steel	<700	√	√	√
		P1.2	quenched and tempered steel	<1200	√	√	√
	P2	P2.1	Alloyed nitrided steel, carburized steel and quenched and tempered steel	<900	√	√	√
		P2.2	Tool steel, bearing steel, spring steel and high-speed steel	<1400	√		√
	P3	P3.1	Tool steel, bearing steel, spring steel and high-speed steel	<900	√	√	√
		P3.2	Tool steel, bearing steel, spring steel and high-speed steel	<1500	√		√

Sloting
Vc (m/min)	fz(mm/Tooth)
	Diameter
	2	4	6	8	10	12	16	20
112	0.01	0.018	0.026	0.034	0.041	0.048	0.06	0.069
92	0.01	0.017	0.025	0.032	0.038	0.045	0.056	0.065
100	0.01	0.018	0.026	0.034	0.041	0.048	0.06	0.069
72	0.009	0.015	0.022	0.028	0.034	0.04	0.05	0.058
64	0.01	0.018	0.025	0.032	0.039	0.045	0.057	0.066
56	0.009	0.016	0.023	0.029	0.036	0.041	0.052	0.06

Roughing
Vc (m/min)	fz(mm/Tooth)
	Diameter
	2	4	6	8	10	12	16	20
228	0.018	0.031	0.045	0.057	0.070	0.081	0.101	0.118
208	0.017	0.029	0.042	0.054	0.065	0.071	0.095	0.11
184	0.018	0.031	0.045	0.057	0.070	0.081	0.101	0.118
144	0.015	0.026	0.037	0.048	0.058	0.068	0.085	0.098
132	0.017	0.03	0.042	0.054	0.066	0.077	0.096	0.112
112	0.015	0.027	0.039	0.05	0.060	0.07	0.088	0.102

Finish
Vc m/min	fz(mm/Tooth)
	Diameter
	2	4	6	8	10	12	14	16	18	20
332	0.028	0.05	0.07	0.091	0.11	0.128	0.144	0.16	0.173	0.186
272	0.026	0.046	0.066	0.085	0.103	0.12	0.135	0.15	0.162	0.173
304	0.028	0.05	0.07	0.091	0.11	0.128	0.144	0.16	0.173	0.186
212	0.023	0.041	0.059	0.076	0.092	0.107	0.121	0.134	0.145	0.155
196	0.027	0.047	0.067	0.086	0.104	0.122	0.137	0.152	0.165	0.177
168	0.024	0.043	0.061	0.079	0.095	0.111	0.125	0.139	0.150	0.161

Note:

If the following carbide end mill cannot meet your requirements, we support OEM customized production. The diameter of 0.2mm to 25mm, the total length of 50mm to 200mm, 4F, 5F, 6F, 8F and logo can be customized, including inch size end milling cutter. Please contact us to select or customize non-standard carbide end mill according to your needs.

Specification	Flute Dia(D)	R angle	Flute Length (C)	Shank Dia(D)	Overall Length(L)
Φ3R0.58d3*50L	3	0.5	8	3	50
Φ3R1.08d3*50L	3	1.0	8	3	50
Φ2R0.55d4*50L	2	0.5	5	2	50
Φ3R0.58d4*50L	3	0.5	8	3	50
Φ4R0.510d4*50L	4	0.5	10	4	50
Φ3R1.08d4*50L	3	1.0	8	3	50
Φ4R1.010d4*50L	4	1.0	10	4	50
Φ5R0.513d5*50L	5	0.5	13	5	50
Φ5R1.025d5*100L	5	1.0	25	5	100
Φ6R0.515d6*50L	6	0.5	15	6	50
Φ8R0.520d8*60L	8	0.5	20	8	60
Φ8R1.028d8*75L	8	1.0	28	8	75
Φ8R2.020d8*60L	8	2.0	20	8	60
Φ8R3.020d8*60L	8	3.0	20	8	60
Φ10R0.525d10*75L	10	0.5	25	10	75
Φ10R1.025d10*75L	10	1.0	25	10	75
Φ10R1.525d10*75L	10	1.5	25	10	75
Φ10R2.025d10*75L	10	2.0	25	10	75
Φ10R3.025d10*75L	10	3.0	25	10	75

Instructions:

1. Before using the carbide end mill, please measure the tool deflection. If the tool deflection accuracy exceeds 0.01mm, please correct it before cutting.

2. The shorter the carbide e extends out of the collet, the better. If the tool extends out longer, reduce the speed, feed speed or cutting amount.

3. In case of abnormal vibration or sound during cutting, please reduce the speed and cutting amount until the situation is improved.

4. Spray type and air jet type are preferred for steel cooling, which can improve the use effect of carbide end mill.

5. Note: Not suitable for low speed machines such as rotary table and electric hand drill.

Applications:

Pre-hardened Steel, stainless steel, Die steel, steel plate, Heat-resistant steel,pipe, copper and aluminum, cast iron, Nonferrous Metal, Wood, Plastic,FRP and sO on. General-purpose operation slotting, rilling, profiling.

Cnc Milling Cutter 6mm 3 4 Flute Tungsten Solid Carbide High Feed Endmill End Mill

FAQ

Q1. The tool breaks when cutting in or pulling out the workpiece

The feed rate and cutting depth can be reduced, and the cutting edge length can be shortened to the minimum of the necessary length.

Q2. Tool breaks during normal machining

Reduce the feed rate and cutting depth.

The tool shall be passivated.

Replace the clamp or spring collet.

The tool with high cutting edge number changes the tool with low cutting edge number to improve chip removal and prevent chip blockage.

Replace dry milling with wet milling (using cutting fluid), and use it with vortex tube gun to reduce tool temperature and avoid tool overheating.

If the wet milling fluid supply direction is changed from the front to the oblique rear or transverse top, the coolant flow should be sufficient.

Q3. The tool breaks when the feed direction changes

(1) Use arc interpolation (NC machine tool), or temporarily stop (temporarily) feeding.

(2) Reduce (decrease) the feed before and after the direction change.

(3) Replace the clamp or spring collet.

Q4. Problem: Part of the blade tip breaks

Chamfer the corners with manual grinding.

Change down milling to up milling.

Hot Products

Cast iron 45 Degree End Mill Cutter Head Grooving Carbide Ball Nose End Mill

Contact Us

Shenzhen Bwin Precision Tools Co., Ltd.

Good Rigidity Carbide End Mill CVD Coated Corner Rounding End Mill

Product Details

Hot Products

Cast iron 45 Degree End Mill Cutter Head Grooving Carbide Ball Nose End Mill

Good Rigidity Carbide End Mill CVD Coated Corner Rounding End Mill

High Precision Tungsten End Mill Keyway Milling Cutter 12mm End Mill

9mm Carbide End Mill Stable Performance Flat End Mill Cutter

R1.5 R4.5 Solid Carbide Ball End Mill Milling Cutter Lollipop Round End Mill

HRC55 Carbide End Mill 6mm Ball Nose End Mill Spiral Endmill Milling Cutter