12v 50ah 780WH 600W Ups Uninterruptible Power Supply Solar Power Generator

YY SERIES

PORTABLE SOLAR GENERATOR KIT

12v 50ah 780WH 600W Ups Uninterruptible Power Supply Solar Power Generator

1. Technical parameter

2. Appearance

1KW-3KW series

3. Installation Instruction

3-1.Open up

After opening the package, please check the accessories, including 1 pc of user manual. And please make sure that the inverter is well-protected after transportation, if any damage:

Note: component miss, do not turn on the machine, feedback to the carrier and distributor.

1). Please retain the packing material, those can be used for next delivery if needed.

2). This series of products is heavy (check attachment as reference), please handle carefully when carrying.

3-2. Installation notice

1). Install in an area of well-ventilated, free of water, burning gas and corrosive stuff.

2). Not good to stand on sides, should keep good air inlet from front panel’s bottom and side face of machine, air outlet from back panel’s fan.

3). Environment temperature should remain from 0 to 40 centigrade.

4). When disassembling and operating under low temperature, it may cause water condense, should not turn on until sides of machine being dry, or it will be shock risk.

5). Install the inverter near mains socket or switch, in order to pull out mains supply plug to cut off power easily when meeting emergency.

Attention:

< Loading should be turned off before connecting to inverter and turned on the loading one by one after connection completed.

< Connect inverter to accessible socket with over-current protection.

< All power sockets should link with ground protection.

< Inverter may have electricity whether input power cable inserts to mains socket or not. Turning off the inverter does not guarantee electricity does not exist. To ensure no output, should turn off all switches and cut the mains power.

< To load inductive appliances such as electromotor, displayer and laser printer, inverter capacity should be two times compared to rated power of the load.

4. Description of panel

Detail of LCD

1 Input Voltage 2 Working Mode 3 Output Voltage

4 Solar Panel 5 Battery Status 6 Loading Application

7 Silent Mode 8 Loading Status

Detail of indicate lamp & button

5. Function and setting

ON/OFF Button: Press for 3 seconds to turn on and 5 seconds turn off.

ENTER Button: Press for 5 seconds start to set Mode P0 to P4. Switch through UP & DOWN button.

Mode P0- Pre-set. Press ENTER 2 times to end up setting. Auto Exit after 10 seconds' no-ops.

Mode P1- Power supply setting. 01- AC supply in priority, 02- Energy saving. 03- Battery supply in priority, switch through UP & DOWN and select through ENTER button.

Mode P2- Battery Type setting. Switch through UP & DOWN and select battery type through ENTER button.

Mode P3- Charging Current 0-35A selecting. 0-20%-40%-60%-80%-100%, Maximum is 35A, Minimum 0A.

Mode P4- Voice setting. Switch the Buzzer through UP & DOWN and select through ENTER button.

6. Connection

Attention:

Terminal and output plug are both available to connect the load. Output plug can only allow the loading under 1500W. Loading over 1500W should connect to terminal.

Solar wiring diagram

Note:

If connect to generator, must follow the steps below:

• Start generator, after it go stably, connect its output port to inverter’s input port (to be sure there isn’t any load connecting to inverter at this moment).
• Start the inverter, connect the loads one by one.
• Choose generator with 2 or 3 times capacity compared to inverter.
• Solar inverter’s panel and connection is different from common model.
• The voltage of solar panel should follow the Technical parameter.

Back panel connection

Note:

If connect to generator, must follow the steps below:

• Start generator, after it go stably, connect its output port to inverter’s input port (to be sure there isn’t any load connecting to inverter at this moment).
• Start the inverter, connect the loads one by one.
• Choose generator with 2 or 3 times capacity compared to inverter.
• Solar inverter’s panel and connection is different from common model.
• The voltage of solar panel should follow the Technical parameter.

7. Care and maintenance

●This series of inverter fairly needs maintenance. Turn to battery charge mode to extend the life of battery.

●discharge and charge the batteries at least 1 time every 6 months. Charging time should not be less than 12 hours.

●In high temperature area, battery should be charged and discharged every 2 months and standard charging time is not less than 12 hours.

●Basically batteries works 3-5 years, should replace when working not well.

●Ask professionals to replace the batteries.

Note:

• Before replacing battery, must switch off battery, inverter and mains supply.
• Put off the metal object like ring, watch etc.
• Use insulated tool and avoid putting any tool and metal object on battery.
• When connecting battery, it may strike some un-harmful sparks.
• Do not make converse connection.

8. Solution for difficult situation