Foxboro FBM207C P0917GY FBM207C P0917 GY

Foxboro FBM207C P0917GY FBM207C P0917 GY

Product Description:

Bulletin 1305 drive parameter data can be programmed and displayed using PLC’s, SLC’s or other logic controllers using an optional Bulletin 1203 Communication Module. The amount of information that can be transferred between the drive and controller is determined by the DIP switch settings on

theCommunication Module. Table B.1 illustrates the dip switch settings for Bulletin 1203-GD1 (Remote I/O) communication modules. Dip switch settings for other communication modules will be similar. Refer
to the appropriate communication module user manual for details.Important: 1305 drives with firmware

revisions FRN1.01 and FRN1.02 are not compatible with Bulletin 1203 Communication Modules. If connected, an error message will be indicated. The red fault status and amber SCANport status LED’s on the front of the module will flash simultaneously.

Contact Information:

Contact:Miya ( manager)

Email :sales@mooreplc.com
Q Q: 2851195450
Skype: miyazheng520
Mobile:86-18020776792 ( what's app )

Related Product Recommendation:

All drives come equipped with a fault LED. When the fault LED is illuminated it is an indication a fault condition exists. Refer to page 2-3 for the location of the fault LED. Once the fault is properly cleared the LED will return to an off state. Diagnostics As can be seen in Figure 2.3, there are two indicators

provided to display the drive’s status condition. The DC Bus Charge Indicator is a neon bulb that will be illuminated when power is applied to the drive. The Fault Indicator is an LED that will be illuminated if a drive fault condition exists. Refer to details on How To Clear a Fault, below.How To Clear a Fault

Important: Resetting a fault will not correct the cause of the fault condition. Corrective action must be taken prior to resetting the fault. To clear a fault perform one of the following:Cycle power to the drive. Cycle the stop signal to the drive. Cycle the [Clear Fault] parameter.

Manual, gives an overall description of the Bulletin 1305 Adjustable Frequency AC Drive (herein called “the drive”) and provides a listing of key drive options. Additionally, this chapter provides information on receiving and handling the drive. MANUAL OBJECTIVES The purpose of this manual is to provide
the user with the necessary information to install, program, start up and maintain the Bulletin 1305 drive. To assure successful installation and operation, the material presented must be thoroughly read and
understood before proceeding. Particular attention must be directed to the ATTENTION and Important statements contained within. Chapter 2 provides instructions on how to mount and wire the drive. It also describes how to operate the drive without a Human Interface Module. Read the Motor Cable Length
section on pages 2-13 – 2-16, and the contact closure inputs information in the Control Terminal Block descriptions on pages 2-19 – 2-21. Chapter 3 defines the display and control panel keys on the optional Human Interface Module. A flowchart is provided to guide the user through the key strokes of the various
menu levels.

Anaheim Automation 23D306S Stepper motor 3.4VDC 2.9A

Bimba Ultran US-1737.125-S Rodless Pneumatic Actuator

Bimba Ultran US-1734.125-S Rodless Pneumatic Actuator

SMC CDRB2BWU20-270S ACTUATOR, ROTARY, VANE TYPE

KLA 94337528 7700m Pittmann Motor 94337528 Microscope driver

KLA 7700m two cables 7 brackets

Asco SC8210G004 Solenoid Valve, 1 In, Orifice 1 In, Brass

KLA 7700m 099660 Handler back plane PCB

KLA 7700m 199958 Rev F PCB PSF Driver SFS75

KLA 7700m Front Panel PCB

KLA Tencor 7700M 181830 Rev D, National Instruments AT-GPIB/TNT

FSI Excalibur Manual 905364-200 Prints and product structures

FSI Excalibur ISR & EOS Manual for sale

FSI Proteus 11 Manual

FSI Excalibur ISR Operation & Maintenance Manual

FSI Excalibur ISR & EOS Systems SECS/GEM implemntation Manual 912629

KLA 8100 PCB 830-10172-000 Rev 3

KLA TENCOR 6420 6400 Calibration Procedure Manual

KLA SURFSCAN 7700 Quartz chuck 150mm - Used

KLA 7700m 174203 Rev D PCB Flat finder pwd Driver

FSI Chemfill systems Manual for sale

Busch DS 700 A DS 700 pump rebuild kit *NEW OEM*

JDS Uniphase 2214-30SLQTT

MAC Pneumatic Solenoid Valve 225B-111BAAA

Ebara PRESSURE SENSITIVE VALVE FOR EBARA FREX 200

ENIDINE MB21539 ADJUSTABLE SHOCK ABSORBER NEW CONDITION IN PACKAGE

92206 NEW, Enidine FP9599 Shock Absorber, 5-1/8" Length, 1" OD

HTC ISO63-100DWCA Double Claw Clamp sheet of 7 each

KLA 7700m EMO Switch

ITW Texwipe TX 5377 HydroCell Nodule Brush QTY3 For EBARA FREX200

The use of the product:

1.glass industry,

2.feed industry,

3.Experienced technichal support team.