|
[China]
Trade Verify
Address: Room 629, 6th Floor, Building 2, Greenland Huichuang Plaza, No. 6 Kexing Road, Guangzhou Private Science and Technology Park, No. 1633 Beitai Road, Baiyun District, Guangzhou
Contact name:Joyce Cui
Guangzhou Tech master auto parts co.ltd |
|
Verified Suppliers
|
|
|
20-175MM Air Suspension Shock Absorber Crimping Tool For Air
Suspension Repair Kits Air Spring Crimping Machine
Production Description
Crimping Force: 100T
Crimping Range: 20mm-175mm
Standard Die Sets: 10 sets (the size can be done as your requests)
Voltage: 380V and 220V(according to customer requests)
Power: 4Kw
System Pressure: 30 Mpa
Accuracy: 0.05mm
Dimension: L850*W900*H1300mm
Gross Weight: 370Kg(includ 10 moulding sets)
Warranty: 12 Months
Appliion: Vehicle Air Suspensions, Air Springs, shock absorber
After Sales Service: We can give technical support for any problem any time
Package: Strong Wooden Box with Pallet
We can offer you 10 moulding sets free .
This machine can be valid to place rings all the usual models such as W164 Front and rear Audi A6 C5, w221, w220, Land Rover BMW and etc.
crimping way : Transverse and Vertical withhold
The brief introduction of high pressure hose crimping machine:
Crimping machine connect rubber, plastic and steel rings through
hydraulic power. It applies locking pressure through the mold of
crimping machine to swage the metal joint on the matched auto air
springs and high-pressure oil pipes, so as to complete the
installation assembly.
It’s applicable to air spring, all kinds of machinery high and low
pressure oil tube, air tube, automobile power steering tube, oil
pipe, gasoline supply pipe, as well as buckling of construction
fittings and hot water pipe.
It’s also widely used in vehicle, engineering machinery,
hydraulic machinery, agricultural machinery and so on.
Installation and Operation
1. Start-up
Connect the electric source well as per the machine requirements,
to make the direction of the motor rotation to be consistent with
the rotation direction marking, and grounding protection shall be
done.
2. Regulating the scale
The scale is used for regulating the amount of the buckling. When
it is regulated clockwise, the buckling amount will decrease, when
it is regulated anticlockwise, the buckling amount will increase.
The scale is connected together with oil cylinder end cover through
three socket head screws and three springs on the scale base. When
using a hand to pull the scale (vertical to the oil cylinder end
cover direction), the scale can flexibly leave from the oil
cylinder end cover. When releasing the scale, the scale will be
recovered relying on spring force. Before the machine is turned on,
inspect carefully if the scale telescoping is flexible and if the
lead connection is reliable.
The primary scale is turned within 0 line of the secondary scale,
turn the machine on for test run, and observe if all actions are
normal. If when the piston conducts reciproing movement, there is a
crawling phenomenon, the bleed screw on the oil cylinder top shall
be unscrewed for exhausting air.
3. Pressure regulation
The buckling pressure and opening mould pressure will be regulated
through two knobs at the back of the oil cylinder, when it is
regulated clockwise, the pressure will increase, when it is
regulated anticlockwise, the pressure will decrease (The pressure
has already been well regulated when ex-factory).
Notices
1. When buckling, make the joint to loe the mould center as much as
possible, the joint is not buckled on the hex nut.
2. Prevent tool and other foreign matter from entering the locking
head.
3. After the work is finished for each time, the eight-block mould
base must be made to extend to the greatest extent, this can make
the spring to be at extension status. If not, the spring will be
damage.
4. When working, the hand should not stretch into the locking head.
5. The power supply must be switched off when maintenance is done.
This is our new hydraulic hose crimping machine, can crimp all
types of hydraulic hoses:
1.
Air spring crimping machine provided with die sets range for 1/4'
to 1 1/4' ID hoses.
2.
Double angular surface-swaging force up to
450T, powerful yet makes crimping easy.
3.
Piston,Cylinder,All dies are wire cut after hardening and grinding.
4.
Powder coating body give it a Futuristic sleek & stylish looks.
Our Customers Normally Ask These Questions About the Machine:
1. What does this machine used for?
It can be used to repair or manufacture air suspensions, air aprings
for cars and trucks. and aslo the industrial hydraulic
hose pipes.
2. What is Voltage of this machine?
Original Voltage is 380V or 220V, but we can also make
according to your requirements
3. Is it simple to learn to opearte this machine?
It is easy for operating. we will give detailed instruction and CD
to show our customers how to operate
4. How to determine the dimensions of the die sets?
We process the die sets according to your dimensions or you tell us
what products you want to crimp, then we can determine the
size.
5. how are you going to package the machine to prevent damage
during shipping?
we will pack the machine with strong wooden box with pallet to
insure the safety of the machine during shipping.
Contact Us:
If you have any questions, please feel free to contact with us. We
would be very glad to help you. We will get back to you within 24
hours or get back to you immediately.
Contact Name: Jennifer Qiu
Skype: 8618819146976
Tel: 0086 18819146976 (WhatsApp)
Wechat:8618819146976
