Shenzhen Firecore Technology Co., Ltd. |
Verified Suppliers
|
|
AHD Car Camera Truck side mounted AHD left and right blind spot monitoring waterproof and shockproof
Figure ( : 1) Line Connection Diagram
4 . Line connection diagram : as shown in Figure (1)
Installation of 5 monitoring systems
1 . 1 Camera installation
Figure (2) Monitoring effect of four cameras
This system requires the installation of four
cameras as shown in Figure
(2) Front facing cameras are divided into two
types dedicated and general - purpose cameras
. Dedicated cameras are installed on the vehicle
emblem as shown in Figure
(3) Universal external cameras can be installed on
air intake grilles bumpers or other suitable
locations
Figure (3) Front view installation rendering
The cameras on both sides are installed on the rearview
mirror as shown in Figure (4)
Figure (4) Installation effect of cameras on both sides
1 . 2 Installation of monitor : Connect the line to the DVD
host according to the wiring diagram .
1 . 3 Installation of the host : After connecting the lines
according to the wiring diagram place the host in a
storage box or install it in a suitable position inside the car
. The vibration sensor is attached to the vehicle body
.
6 . Operation method of panoramic monitoring system
There are two modes of operation for the monitoring system :
automatic mode and manual mode . Automatic mode and manual
mode can be used together simultaneously . The manual mode
can be controlled through the steering lever or membrane switch
(optional) and the control of the steering lever
and membrane switch is consistent
360 ° panoramic monitoring system display screen switching
operation method
(1) Four screen : When the car
starts the host and camera start to
work and the screen is in an H - shaped four split
mode displaying four screens :
"front" "back" "left" and
"right" (hereinafter referred to as the basic screen mode) .
After a delay of 15 seconds the display automatically turns
off and switches to navigation and audio mode but
the entire system is still in recording mode .
(2) Front view : In the basic graphics mode
the front camera works by using the film switch or
lifting the steering lever upwards . The display screen
displays the front view of the car separately
Press the film switch again or lift the steering lever
upwards to turn off the display and switch to navigation and audio
mode
(3) Rear view : When reverse gear is
engaged the display automatically switches to the
reverse view screen which is the rear view
display mode . If you exit reverse gear, turn off the
rearview display mode and automatically enter the basic screen mode
. After a delay of 15 seconds the display
will automatically turn off and switch to navigation and audio
mode .
(4) Side view : In the basic graphics mode
when turning on the left or right turn lights
the display screen switches to the left and right
display modes cancels the turn signal
and the screen automatically switches to the basic
graphics mode with a delay of 5 seconds to turn
off the display and switch to navigation and audio mode
(5) Side and rear view : When reverse gear is engaged and
turn signals are turned on the display screen
switches to a three screen display mode where the
lower half of the display screen displays the reverse rear view
screen and the upper left corner displays the front left image of
the car . The upper right corner displays the front right
image of the car . On this basis exit
reverse gear and when the turn signal is powered
on the display screen switches to the left and
right display modes . The left side displays the left front
screen of the car and the right side displays the
right front screen of the car . When the turn signal is
cancelled the screen automatically switches to
the basic screen mode with a delay of 15 seconds
to turn off the display and automatically switch to the navigation
audio mode .
(6) During the operation of the car pressing the
membrane switch or lifting the steering lever upwards can enter the
basic screen mode .
(7) When controlling the steering lever the lever
can only be lifted once at a time . If you need to enter the
next screen you need to pause for one second
before operating . Continuous operation for more than two
times is invalid . Thin film switch is optional .
(8) When using the headlights at night the
steering lever control is ineffective . In this
case press the dual flashing lights to trigger and
then turn off the dual flashing lights . At this time
the system enters basic mode and the
operation method for switching the display screen is shown in steps
(1) - (7).
We are a professional manufacturer of research and development production and vehicle monitoring
Car video recorder car camera car usb camera car display usb camera
Please contact us by email : firecore1688@163.com
WeChat and phone : 0086+13823606792