Shenzhen ZXT LCD Technology Co., Ltd. |
Verified Suppliers
|
|
32" 40" 42" 43" 46" 47" 50" 55" 60" 65" 70" 80'' 84'' Multi Touch Screen Film,Capacitive Touch Film 10 Touches
The Interactive Touch Foil
foil that manufactured by ZXT. Quickly enabling a touch screen in
your ordinary glass world. 's large format flexible touch panel,
cover from 30 to has 3 key parts. 1st is film sensor, 2nd is
electronics controller, we call it eBoard, 3rd is driver. Film
sensor is a green technology product, has high transparency, light
and thin. the embedded nano wire grid is a sensor network, that can
precisely positioning hands touch action. It use sensing
technology, easily change an to bulletproof touch screen. eBoard
use SoC architecture, so the PCB is small and strong noise
filtering algorithm, It can detect weak signal that caused by
hands.
Driver support Windows XP/7/8, include 32 bit and 64 bit. sion, Mac
OS X, Android 4.0 up version. has two version, one is cling film
version, It designed for interactive window and could be peeled off
for reusing. Another is permanent version, once you peel off the
cover layer and laminate onto the glass. the sensor will be
permanently fixed. fi and bulletproof are the application can
fulfill with this requirement. It Will bring added and fun to use
What is the ZXT interactive foil?
Interactive foil is a clear lightweight touch foil that can be
applied under or behind any non-metallic substrate to create a
through material (glass) touch system.
How does it work?
The interactive foil uses projective capacitance. When a users
finger or gloved hand comes close to the surface it causes a
disturbance in the electrical field which is then detected as a
touch event, the position of the touch is then precisely
calculated.
What thickness of material can the touch foil work through?
The touch foil can work through non-metallic materials up to 16mm
thick. We do recommend testing materials thicker than 10mm.
Will it work through double-glazing?
The touch screen can work through double-glazing. To achieve this
the controller board has to be modified in the factory. This
modification slows the refresh rate of the touch screen. Due to
this only touch functions are available in this mode rather than
drag and touch. We recommend site testing in all cases to check
functionality since double glazing specification vary widely.
What are the typical uses of the interactive foil?
Through window system using rear projection or LCD as the display
technology.
Integrated with LCD displays for creating kiosks or stand-alone
touch screens.
Under table tops for using LCD or projectors from above for the
display technology.
What sizes are available?
The foil comes in standard 4:3 format from 30" to 80" and 16:9
format from 32" to 100" Special custom sizes are also available.
What is the largest foil size I can buy.
The width is 120 cm and length is 220 cm.
Please call ZXT to discuss requirements.
How is it fixed?
The touch screen can be fixed using either a permanent or
non-permanent adhesive system. The system used is dependant on the
application.
The non-permanent system is designed to be for used on glass only, it is an ideal system for retail applications where you may wish to remove and recover the touch foil for future promotions.
Our permanent system uses an optically clear system ideal for applying to glass and other non-metallic substrates. Best used where a permanent fixing is required and when the touch screen is being used in a range of more rugged environments.
Both systems use a wet lamination process. Laminating instructions are available
Will the touch foil work through Glass?
This type of glass uses a metal in the manufacturing of the glass
so the touch foil will not work through this material. Other metal
tints also stop the foils working.
What are the key benefits of the ZXT interactive foil?
Will it work with LCD displays?
The touch foil can be used with LCD displays.
As a through window touch unit the touch foil is first applied to
the window and then the LCD unit is fixed behind the touch foil.
The touch foil can also be integrated inside LCD units. The foil will need to be applied to a substrate, there is a requirement for an 6-8mm air gap between the LCD panel and the back of the touch foil the air gap is dependant upon the noise generated by the LCD panel. It is also necessary to ground the controller unit to the case of the LCD unit.
Will it work with Plasma displays?
No these displays generate too much electrical noise
Does the foil have a front and a back?
The foil does not have a front or back, However when the unit is
supplied with a integrated double release fixing system the foil is
applied on one side only.
Must the controller board be at the bottom?
No the unit can be applied with the controller at the top or bottom
the foil can also be supplied with the controller on the side.
Can I use cling film with Acrylic?
For a short period (testing the unit) over a longer period the
cling film will migrate into the acrylic making a permanent bond
with the acrylic.
How long is the serial cable?
Standard cable supplied is 6M, we also have a 15M cable as an
optional extra
Can I have longer cables?
It may be possible to use up to 25M however you may experience
additional noise, which can make the system unusable. In these
situations we would recommend the use of a suitable RS 232 booster
or a RS 232 to Cat5 converter system.
How do I connect to a USB computer port?
You can use a USB to serial converter device these are available as
an optional extra
What is the power required for the touch screen?
The touch screen is powered from the RS232 port and requires
between 5-12v
Can I have 2 foils next to each other?
Yes and no!
It is not possible to have two touch foils on the same piece of
glass
There is a requirement to have an air gap between two foils
It is also possible that the touch foils will need to be insulated
from each other
Can I use foils with other substrates, for example wood for
interactive tables?
Yes the touch foil can work through any non-metallic material, we
recommend testing of the substrate to check the functionality.
My calibration points are outside the display area, can I adjust
this?
Yes we can provide instructions on how to do this
The touch foil is not responding, how do I check what the problem
is.
Please refer either the quick start guide or full user manual for
fault-finding instructions.
How do I use the cling film?
Laminating instructions are supplied with the touch foil, they can
also be found on the CD supplied with the touch foil.
How many times can I remove the foil and re fix it using the cling
film.
It is possible to re-use the cling film if it is kept in good
condition between installations. However we would recommend a new
piece be used for best quality installation.
Technical troubleshooting FAQ
I have a foil installed in front of and LCD and the cursor keeps jumping to the top of the screen randomly
This is caused by interference with the outermost wire in the foil.
To remedy the problem try:-
Interactive touch foil technical specification
ITEM | Interactive touch foil |
Detection Method | Improved Projected Capacitance Touch technology using a horizontal and vertical XY array of sensing wires |
Size | 30" - 72" (4:3) 30" - 100" (16:9) |
Customization features | Sizes, Tail Length, Tail Width, Tail Position, Active Area, Cut Size |
Fixing Options | Removable and Permanent options available |
Position Accuracy | Approximately 3mm absolute, 1mm relative, No Drift |
Alignment | Software drivers provide a calibration facility |
Number of Electrode | 64 way |
Sensitivity | Can be programmed for different thickness of glass and even use
with gloved hands. Standard configuration functions with non-metallic single construction glass 25mm thick inclusive of glass and air gap. Sensitivity through Double Glazing also possible |
Scan frequency | 30Hz |
Output | USB 2.0, Male A to Male Mini B |
Driver Compatibility | Windows2000, Windows XP, Windows 7, Windows 8 (32 Bit / 64 Bit) |
MAC OS X Lion Linux(Ubuntu) Android (4.0↑, Depends on customization) | |
Touch Function | mouse function and multi-touch 2 points(support TUIO & Windows Native) |
Temperature Range | Better than -20°C to +80°C |
Humidity Control | 0%-95%. Unaffected by condensation |
Light Transmission | Typically better than 93% |
EMC | EN 61000-6-1:2007, EN 61000-6-3:2007+A1:2011 |
Power | Maximum 0.5w |