Ford IDS Vehicle Communications & Measurement Module Base Kit
VCMM
The Vehicle Communication & Measurement Module (VCMM) combines
all of the functionality of the VMM, VCM II, and MTS 4000/4100
vibration analyzer in an industry-leading one-box solution. The
Advanced kit includes all components and functionality found in the
base kit P/N 164-R9822 along with the advanced driveline balance
kit and secondary ignition testing capability. This is the same kit
found in all the Ford Dealerships and will cover all Ford Makes
Trucks, Cars, Gas, Diesel 1996 - Current Year.
The Kit Includes:
- Ford VCMM Advanced Kit, VMM, VCM 2, Vibration Analyzer, and
Oscilloscope
- All Cables and Wireless Module Included
- Full Factory 2 Year Industry Leading Warranty
The Base Kit Does Not Come with a Software License (Sold
Separately)
FORD VCMM
DIAGNOSTIC CAPABILITY (DOES IT ALL)
- Retrieve CMDTC's
- KOEO (Key-On-Engine-Off)
- KOER (Key-On-Engine-Running)
- Data logger
- Body
- Chassis
- Electrical
- Powertrain
- Pressure/Vacuum Tests
- Network Test
- Module Programming
- Programmable Module Installation
- Module Reprogramming
- Programmable Parameters
- Body Tools
- PATS Functions
- *See Note Below
- Remote Keyless Entry
- Factory Keyless Entry Code
- Restraints
- Chassis Tools
- Bleed anti-lock brakes
- IVD Initialization Sequence
- Ride Height Calibration
- Pneumatic Test
- Accurate Trim Test
- Electrical Tools
- Charging System Test
- Parking Aid Switch Test
- Audio
- Powertrain Tools
- EVAP Test
- Fuel Economy Test
- Fuel System Test/RelativeInjector Flow Test
- (VCM and VMM modules are required on some vehicles)
- Ignition System Test
- Spark Duration PIDs
- Power Balance Test
- Relative Compression Test
- Transmission Test
- (IDS - Some vehicles require only VCM)
- Engine Checks and OBD Tests
- (Drive Cycle, Mode 01, Mode 06 & Mode 09)
- EGR Test
- Other Powertrain tests & functions
Key Features:
- Vehicle Communication (VCM II capability)
- Customer Flight Recorder capable
- 4-Channel Oscilloscope
- 4-Channel Digital Multi-meter
- 5th-Channel direct monitoring of the DLC connector
- Vibration Analysis
- Driveline Balance*
- Signal Generator
4/5 Channel Oscilloscope
- The improved user interface from VMM
- Four independent differential Input Channels enable independent
monitoring of signal types such as monitoring voltage while
concurrently measuring the voltage drop across the circuit.
- A Fifth High-Speed Channel that can directly monitor CAN signals at
the DLC connector
- Capture/Record capability to assist in capturing intermittent
issues
- Advanced Triggering capability
- Pre-Configured setup configuration for common signals and
procedures
- New “Time/Angle” time-based settings (CKP/CMP timing diagnostics)
Vibration Analysis and Driveline Balance
- Similar functionality to the MTS 4000/4100
- Improved user interface with reduced configuration and setup time
- Color display
- Record capacity
- “Strobe light Pick up loop” for improved component identification*
- Optional second vibration transducer*
- Optional Dual Plane driveline balance*
*Requires Advanced Kit (164-R9823)
The Digital Multi-Meter
- Monitor up to four independent readings at the same time
- Capture/Record history
- Graphing capability for up to two channels
- Voltage, Current, Resistance, Pulse Width, Duty Cycle, Frequency,
and Period
Signal Generator
- User-configurable settings for signal waveform types: sine, square,
triangle, pulse generator, DC voltage and arbitrary.
- Verify integrity of module input wiring and the module hardware
- Improved interface and greater adjustability of voltage and
frequency.
System Requirements
- The VCMM will run on any Windows 7 or higher operating system that
has 8GB of RAM or higher.
- IDS software subscription required.