|
[China]
Trade Verify
Address: 701, Yongchang Building, Xicheng Industrial Zone, Xixiang, Bao'an District, Shenzhen, China 518126
Contact name:Sunny
Shenzhen Qianhai Lensen Technology Co., Ltd |
|
Verified Suppliers
|
|
|
100mW Wireless Control Module 433MHz Wireless Data Module For 500m Mini Size
LS-S100 is a Mini-size RF transceiver. It is usually used for restricted space application. With TTL interface, it is widely used for micro-controller wireless communication and other TTL level port communication systems. It has high reliability and good performance.
I. Technical specification
| PERFORMANCE | |
| Power Output: | 100mW(Default), |
| RF Line-of-sight Range: | 1000m@1200bps; 600m@9600bps |
| RF Effective Rate: | 1200/2400/4800/9600/19200bps |
| Space Channel: | 1MHz(Default),(12.5/25KHz/other customization ) |
| Bandwidth: | <25KHz |
| Receiver Sensitivity: | -123dBm@1200bps(1% BER) |
| NETWORKING | |
| Networking Topology: | Point-to-point, point-to-multipoint |
| COMPATIBILITY | |
| LS-U Series | |
| POWER | |
| Supply Voltage: | 5V DC (default), |
| Transmit Current: | 100mA |
| Receive Current: | 30mA |
| Sleep current: | 10uA |
| GENERAL | |
| Communication Mode: | Half-duplex |
| Frequency Band: | 433MHz (400/450MHz/470MHz) |
| Channel: | 8(default),16/32/64(optional) |
| Interface: | TTL |
| PHYSICAL PROPERTIES | |
| Size: | 28mm×15mm×10mm (excluding antenna base and data pin) |
| Weight: | 20g |
| Antenna Base: | 50Ω, SMA |
| Operating Temperature: | Industrial:-40℃~+85℃(TCXO) |
| Frequency Stability: | ±2.5ppm Industrial |
II. Application Field
LS-S100 the micro power wireless transceiver data module is suitable for:
* Wireless alarm and security systems
* Wireless scanner
* Building automation, security, wireless monitoring and control
* Wireless data transmission, automatic data collection system;
* Sports training & competition;
* Wireless POS, PDA wireless smart terminal;
* Wireless telemetry charging for parking, parking lot;
* Wireless modem Automobile inspection and four-wheel orientation;
* Point to multi-point wireless network
......
III. How to Use It
1. Default 5V Power supply
2. PIN Definition (6pin)
Table 1: JP1 Pin Definitions and connection methods
| Pin No. | Signal Name | Function | Level | Connection with terminal | Remarks |
| 1 | GND | Grounding of power supply | - | Ground | |
| 2 | VCC | Power supply: DC 5V | - | ||
| 3 | RXD/TTL | Data receiving | TTL | TxD | |
| 4 | TXD/TTL | Data transmitting | TTL | RxD | |
| 5 | SLP | Sleep control | - | Sleep signal | Low level valid |
| 6 | TEST | Factory testing | - | - |
3. Installation dimension
4. Parameter setting by our software
You can use our software Lensen.exe to read or set the parameter on computer. When you connect RF module to PC by the testing cable, please remember to connect the DB9 as well as USB port to computer.
Corresponding frequency points at 433MHz of 1-8 channels
| Channel | Frequency | Channel | Frequency | Channel | Frequency | Channel | Frequency |
| 1 | 429.0325MHZ | 2 | 430.0325MHZ | 3 | 431.0325MHZ | 4 | 432.0325MHZ |
| 5 | 433.0325MHZ | 6 | 434.0325MHZ | 7 | 435.0325MHZ | 8 | 436.0325MHZ |
5. Standard package
(a). One LS-S100 RF module
(b). One 6-pin ribbon cable
(c). One coil antenna
If you have special requirements, please contact us for more details.
