Jinan Should Shine Didactic Equipment Co., Ltd. |
|
SR6131 Fluidisation and Fluid Bed Heat Transfer Unit Teaching Equipment Hydrodynamics Lab Equipment
Specification
examination of the fluidised bed formation and the heat transfer in the fluidised bed
fluidised bed of compressed air and aluminium oxide, particle sizes either 100µm or 250µm
glass reactor, backlit
glass reactor with sintered-metal plate at the inlet and air filter at the outlet
heating element, submersible and with adjustable power output
manual setting of the air flow rate via valve and flow meter
sensors with digital displays for temperature at heater, air inlet, in fluidised bed, pressure upstream of the reactor and in the fluidised bed, air flow rate, heating power
steel rulers for measuring the immersion depth of the heating element and the height of the fluidised bed
safety valve, temperature switch at the heater, air filter at the outlet
GUNT software for data acquisition via USB under Windows 7, 8.1, 10
Technical data
Glass reactor
capacity: 2150mL
filling volume: approx. 1000mL
operating pressure: 500mbar
Heating element
power: 0…100W
Measuring ranges
temperature: 1x 0…100°C, 2x 0…400°C
flow rate: 0…15Nm3/h
pressure: 1x 0…25mbar, 2x 0…1600mbar
power: 0…200W
230V, 50Hz, 1 phase
230V, 60Hz, 1 phase; 120V, 60Hz, 1 phase
UL/CSA optional
Dimensions and weight
LxWxH: 910x560x800mm
Weight: approx. 65kg
Range 0 to 1000 W approx. (Nominal heater power 400 W)
Range
0.15 to 3.5 l / s approx.
Fluidization and Fluid Bed Heat Transfer Unit The rate of heat transfer from the heater is
must be adjusted for manual electronic control and digitally displayed. Two thermocouples are built into the surface of the element. One of them indicates surface temperature, and the other, in combination with
controller, prevents the surface temperature of the heater exceeding the set value (up to 200 °
Digital temperature indicator with selector displays
element temperature, air supplied to
distributor and movable probe in the chamber of the bed.
Two liquid-filled pressure gauges are installed. One displays air pressure at any level in the chamber of the bed, and
the other shows the pressure drop in the hole, from
which can be determined by higher air flow rates. four sorts of fused alumina (alumina) bulk grains
come with the device and they are suitable for
a wide range of fluidization and heat transfer experiments. An important feature of this device is the ease with which
The material of the bed is subject to change. The block may be in
operation again after two or three minutes.
Data sheet
Granule material: fused alumina or similar
Four grades of granules are supplied
Bedroom: approx. Ø105 x 220 mm
Panel: high-quality impact-resistant plastic, on which the following components are installed:
Electronic control to adjust the power consumption of the heater.
Digital wattmeter to indicate heater power consumption. Range 0 to 1000 W approx. (Nominal heater power 400 W)
Flow meters for measuring air flow through a bed. Range
0.15 to 3.5 l / s approx.
Digital thermometer for temperature indication
heater surface, air intake and probe. Resolution 1 ° C.
Product Details and Warranty
We supply suitable spare pats according to experiment requirement, our products take aluminum structure, A4 paper dimension aluminum and plastic hanging box structure.
We supply 3 years warranty time.
Packaging & Delivery
Package details: plastic film+ plastic foam + plywood box with pallet, and for equipment dimension less than 1CBM, we supply plastic film+ plastic foam+ fine carton.
Arrange delivery within 45 days upon receipt of payment.
Please see below photo for detailed package.
Training Room Photo
Company Information
We supply professional educational training equipment and technical teaching equipment, which has been widely applied in Engineering Universities, Polytechnics, Technical Institute, Vocational Schools as well as Industry workforce Development Programs and Training Center. Our products allow students to learn and experiment through valuable hands-on experience, and the technology covered by our training equipment provides knowledge, experiments and didactic skills development that are of critical importance to today´s and tomorrow´s careers.
Photo for Clients Visiting Factory
Service
We supply supply7*24 hours service, customer design service, OEM service, buyer label service. With professional engineers team and sales team, we assure you good product quality.
Certificate
Our products takes ISO9001 product management system.
No. | Feature Name | Details |
1 | Customer design | Yes |
2 | Warranty | 1 year, 2 years, 3 years or 5 years according to client requirements |
3 | Package | Plastic film+ carton+ Fine plywood |
4 | Products standard | International didactic equipment standard |
5 | Application range | Educational equipment for university, college, vocational training centers |
6 | Company philosophy | Supply best quality Chinese products to the worldwide schools. |
7 | Self owned brand | Shouldshine, SSEDU, JSS. |
8 | Production time | From 10 days to 60 days according to different items |