Home Companies Guangzhou Concord Sound Industrial Co., Ltd.

VATASA 2 Channel Audio Power Amplifier 600W 800W 1000W Customized

Contact Us

[China]

Trade Verify

Address: No. 36 Daping Industrial, Shatou street, Shiqiao, Panyu District, Guangzhou City, Guangzhou, Guangdong, China

Contact name:Xia

Guangzhou Concord Sound Industrial Co., Ltd.

Verified Suppliers

Trust
Seal
Verified
Supplier
Credit
Check
Capability
Assessment

VATASA 2 Channel Audio Power Amplifier 600W 800W 1000W Customized

Country/Region	china
City & Province	guangzhou guangdong
Categories	Speakers

Product Details

Product Description

VATASA Series professional 600W 800W 1000W 2 channel audio high power amplifier

1.Mains Power Switch
When press the switch, the soft start circuit run for avoiding surge strike. In about 3-4 seconds, there will be a
clicking denote that soft start finished. And more 1-2 seconds later, there will be another “clicking”, the amplifier
is connected with speaker and ready to work.
2.CH-1/CH-2 Input level control
Adjust it to get the volume desired. Use CH-1 control only while amplifier is set in Bridge or Parallel mode.
3.Signal LED
The green signal led indicates that a music signal is present at this channel input.
4.CH-1/CH-2 Protection indicating LED
This red LED will light up when the amplifier is running un-stable or went in to thermal protection after the power
elements temperature over 90℃.
5.Clip LED
Turns on just before the maximum, distortion free, output level of the amplifier. The clip leds may turn on shortly from
time to time but they may certainly not turn on for longer periods. In this case you have to turn the output level down!

6.Bridge mode indicating LED
Indicate the amplifier is working under BRIDGE mode, the indicator is lighten , and the input signal only acts on CH-1
7.Parallel mode indicating LED
Indicate that the amplifier is working under parallel mode, the indicator is lighten, input signal only acts on CH-1.
8.Stereo mode indicating LED
These green LED will light up while the input signal is connected, the amplifier is working under stereo mode.

1.MAINS POWER SUPPLY CORD
2.CH-1/CH-2 SPEAKON OUTPUT
Used by a standard SPEAKON connector.
3.CH-1/CH-2 BINDING POST OUTPUT
Used by a standard binding connector.
4. OUTPUT MODE SET SWITCH.
BRIDGE MONO MODE. Sends CH-1 signals out-of-phase to CH-2,producing twice the normal voltage swing
between the two RED speaker terminals (CH-1 RED is defined as positive).Only CH-1 controls and input are effective.
STEREO MODE. Each channel operates independently.as usual.

PARALLEL INPUT MODE. Sends CH-1 signals out CH-2,Only CH 1 controls and input are effective.
NOTE: speaker connections work as usual,Never connect the red output terminals directly together.
5.CH-1/CH-2 XLR INPUT CONNECTOR
Standard XLR (male) socket for input signal link.
Pin1: signal ground, Pin2: signal+, Pin3: signal-
6. CH-1/CH-2 XLR OUTPUT CONNECTOR

Specification

	H-6	H-8	H-10
Power handling	600W2(8Ω)/900W2(4Ω)	800W2(8Ω)/1200W2(4Ω)	1000W2(8Ω)/1500W2(4Ω)
Signal to noise ratio	≥ 95dB			≥ 95dB	≥ 95dB
Output interface	Speakon and Binding			Speakon and Binding	Speakon and Binding
Input sensitivity	0.775V			0.775V	0.775V
Input impedance	20kΩ/Balanced,10kΩ/un-Balanced			20kΩ/Balanced,10kΩ/un-Balanced	20kΩ/Balanced,10kΩ/un-Balanced
Distortion	≤ 0.03%			≤ 0.03%	≤ 0.03%
F=1KHz 8 OHMS	> 240			> 240	> 240
Frequency response	20Hz-20kHz, ±1dB			20Hz-20kHz, ±1dB	20Hz-20kHz, ±1dB
Power supply	AC: 220-230V 50Hz			AC: 220-230V 50Hz	AC: 220-230V 50Hz
NW(kg)	10.6	12.4	13.5
*Size(wdh)*	48232688mm			48232688mm	48232688mm