Active Member
|
[China]
Address: 18F, Building 2, Nantai Yunchuanggu, Phoenix Community, Guangming District, Shenzhen, Guangdong, China
Contact name:Amy
Shenzhen FRIDA LCD Co., Ltd |
|
|
11.6 Inch 1920x1080 Tft Lcd All Viewing Angle 30 Pin Edp 220 Nit
General Description:
The manufacturer of M116B30-040-121-0102 is BOE. The display mode is Normally black. The contrast ratio is 1000:1, the color saturation is 72%NTSC, the response time is 25 ms, the optimal viewing Angle is symmetrical, the operating temperature is 0℃ to +50℃, and the storage temperature is -10℃ to +60℃.
Specifications:
| Parameter | Specification | Unit | Note |
| Display size | 11.6” (Diagonal) | inch | |
| Active area | 256.32(H) ×144 . 18(V) | mm | |
| Pixel Format | 1920(H) ×1080(V) (1pixel = R + G + B dot) | pixel | |
| Pixel pitch | 0.1335(H) x 0.1335 (V) | mm | |
| Pixel configuration | R, G, B vertical stripe | ||
| Display mode | Normally black | ||
Surface treatment of front polarizer | Anti-glare coating: (3H) |
Interface Connection:
| Pin No. | Symbol | I/O | Function | Remark |
| 1 | CABC_EN / NC | - | Reserved for CD | [Note1] |
| 2 | H_GND | P | High Speed round | [Note2] |
| 3 | Lane1_N | I | Complement Signal Link Lane 1 | |
| 4 | Lane1_P | I | True Signal Link Lane 1 | |
| 5 | H_GND | P | High Speed round | [Note2] |
| 6 | Lane0_N | I | Complement Signal Link Lane 0 | |
| 7 | Lane0_P | I | True Signal Link Lane 0 | |
| 8 | H_GND | P | High Speed round | [Note2] |
| 9 | AUX_CH_P | I | True Signal Auxiliary Channel | |
| 10 | AUX_CH_N | I | Complement Signal Auxiliary Channel | |
| 11 | H_GND | P | High Speed round | [Note2] |
| 12 | LCD_VDD | P | LCD logic and driver power(3.3V) | |
| 13 | LCD_VDD | P | LCD logic and driver power(3.3V) | |
| 14 | NC | I | Reserved for LCD manufacturer’s use | [Note1] |
| 15 | LCD_GND | P | LCD logic and driver ground | |
| 16 | LCD_GND | P | LCD logic and driver ground | |
| 17 | HPD | O | HPD signal pin | |
| 18 | LED-1 | P | Backlight ground | |
| 19 | LED-2 | P | Backlight ground | |
| 20 | LED-3 | P | Backlight ground | |
| 21 | LED-4 | P | Backlight ground | |
| 22 | BL_ENABLE | I | Backlight on/off | |
| 23 | BL_PWM_DIM | I | System PWM | |
| 24 | SCL/NC | - | Reserved for LCD manufacturer’s use | [Note1] |
| 25 | SDA/NC | - | Reserved for LCD manufacturer’s use | [Note1] |
| 26 | BL_PWR | P | Backlight power | |
| 27 | BL_PWR | P | Backlight power | |
| 28 | BL_PWR | P | Backlight power | |
| 29 | BL_PWR | P | Backlight power | |
| 30 | NC | - | Reserved for LCD manufacturer’s use | [Note1] |
CN1 (eDP signals , +3.3V DC power supply and B/L power supply)
[Note1] Don’t input any signals or any powers into a NC pin. Keep the NC pin open.
[Note2] The shielding case is connected with signal GND.Connector used :20455-030E-76(I-PEX),Corresponding connector : 20453-030T (I-PEX)
Absolute Maximum Ratings:
| Parameter | Symbol | Condition | Ratings | Unit | Remark | |
| MIN | MAX | |||||
| +3.3V supply voltage | VDD | Ta=25℃ | -0.3 | +3.6 | V | |
| Backlight supply voltage | VBL | Ta=25℃ | -0.3 | +21 | V | |
| Input voltage(eDP) | VI | Ta=25℃ | -0.3 | +1.5 | V | |
| Input voltage(BL) | VBL_I | Ta=25℃ | -0.3 | VDD+0.3 | V | |
| Storage temperature | Tstg | -10 | +60 | ℃ |
| |
| Operation temperature | Topa | 0 | +50 | ℃ | ||
“Absolute Maximum Ratings” is regulations that do not exceed it even momentarily.
Stress beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
Backlight Driving:
The backlight system is an edge-lighting type with white-LED.
(It is usually required to measure under the following condition: Ta=25C±2C)
| Parameter | Symbol | Min. | Typ. | Max. | Unit | Remark |
| Supply voltage | VBL | 7.0 | 12.0 | 21.0 | V | |
Current dissipation | IBL | - | (227) | (251) | mA | VBL=12V Duty Ratio=100% |
| (135) | (135) | mA | VBL=7.9V Duty Ratio=40% | |||
| Modulated light signal voltage | VPWM H | 1.85 | - | VDD | V | |
| VPWM L | 0 | - | 0.7 | V | ||
| Brightness Control Duty Ratio | Duty | 1 | - | 100 | % | |
| Brightness Control pulse width | TPWM | 5 | - | - | ps | |
| Brightness Control frequency | PWM | 200 | - | 2,000 | Hz | |
| LED-BL ON/OFF High voltage | VCNT H | 1.8 | 3.3 | 3.6 | V |
Optical Specification:
| Paramete | Conditions | Min. | Typ. | Max. | Unit | |
Viewing Angle(CR>10) | Horizontal | L | - | 89 | - | degree |
| R | - | 89 | - | |||
| Vertical | T | - | 89 | - | ||
| B | - | 89 | - | |||
| Contrast Ratio | Center | 700 | 1000 | - | - | |
| Response Time | Tr+Td | - | 25 | ms | ||
CF Color Chromaticity(CIE1931) | Red x |
Typ. -0.05 | TBD |
Typ. +0.05 | - | |
| Red y | TBD | - | ||||
| Green x | TBD | - | ||||
| Green y | TBD | - | ||||
| Blue x | TBD | - | ||||
| Blue y | TBD | - | ||||
| White x | (0.313) | - | ||||
| White y | (0.329) | - | ||||
| NTSC ratio | % | (72) | - | |||
| Luminance of white | YLI | 220 | cd/m | |||
Handling Precautions:
1.Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets inside your eye or mouth by mistake.
2.If a minute particle enters in the module and adheres to an optical material, it may cause display non-uniformity issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a fan.
3.Do not expose the LCD module to a direct sunlight, for a long period of time to protect the module from the ultra violet ray.
Reliability Test Items:
| No. | Test Item | Conditions |
| 1 | High temperature storage test | Ta=60℃ 72h |
| 2 | Low temperature storage test | Ta=-10℃ 72h |
| 3 | High temperature & high humidity operation test | Ta=40℃90%RH 72h (No condensation) |
| 4 | High temperature operation test | Ta=50℃ 72h |
| 5 | Low temperature operation test | Ta=0℃ 72h |
