Active Member
|
[China]
Address: 18F, Building 2, Nantai Yunchuanggu, Phoenix Community, Guangming District, Shenzhen, Guangdong, China
Contact name:Amy
Shenzhen FRIDA LCD Co., Ltd |
|
|
15 Inch Tft Screen 1024x768 Full Viewing Angle Lvds Interface 20 Pins
General Description:
DV150X0M-N10 operation mode ADS, constant black display, transmissive , support color 16.7M , 72% NTSC, light source type WLED, 50K hours , including LED driver, weight 930g.
Features:
Specifications:
| Parameter | Specification | Unit | Remarks |
| Active area | 304. 128(H) × 228.096(V) | mm | |
| Number of pixels | 1024(H) × 768(V) | pixels | |
| Pixel pitch | 0.297(H) × 0.297(V) | mm | |
| Pixel arrangement | Pixels RGB Vertical stripe | ||
| Display colors | 16.7M | colors | 6bits+FRC |
| Display mode | Normally Black | ||
| Dimensional outline | 326.5(H) × 253.5(V) × 9.7(Total) | mm | Detail refer to drawing |
| Weight | 930 | g | |
| Power Consumption | 8.72 | Watt | Typ. |
| Bezel width (L/R/U/D) | 10/10/11.7/11.7 | mm | |
| Surface Treatment | Haze 25%, 3H | ||
| Back-light | E-LED Light bar Type | ||
| LED life | 50000 | ||
| Display Direction | landscape & Portrait |
Absolute Maximum Ratings:
The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table.
| Parameter | Symbol | Min. | Max. | Unit | Remark |
| Power Supply Voltage | VDD | -0.3 | 4 | V | Ta = 25℃ |
| Operating Temperature | TOP | -20 | +70 | ℃ | Note 1 |
Storage Temperature | TSUR | -20 | +70 | ℃ | |
TST | -20 | +70 | ℃ | ||
| Operating Ambient Humidity | Hop | 10 | 90 | %RH | |
| Storage Humidity | Hst | 10 | 90 | %RH |
Note 1 : Wet bulb temperature should be 39℃ max. and no condensation of water.
Electrical Specifications:
| Parameter | Symbol | Values | Unit | Remark | |||
| Min | Typ | Max | |||||
| Power Supply Input Voltage | VDD | 3.0 | 3.3 | 3.6 | V | Note 1 | |
| Power Supply Current | IDD | - | 410 | 740 | mA | ||
| Power Supply Ripple Voltage | VRP | - | - | 300 | mV | ||
| Rush Current | IRUSH | - | 2 | 3 | A | Note 2 | |
LVDS Interface | Differential Input High Threshold Voltage | VLVTH | - | - | +100 | mV | VLVC=1.2V |
Differential Input Low Threshold Voltage | VLVTL | - 100 | - | - | mV | ||
| Common Input Voltage | VLVC | 0.7 | - | 1.6 | V | ||
CMOS Interface | Input High Threshold Voltage | VIH | 0.7VDD | - | VDD | V | |
Input Low Threshold Voltage | VIL | 0 | - | 0.3VDD | V | ||
Power Consumption | PD | 0.8 | 1.3 | W | |||
| PBL | 7.92 | 8.71 | |||||
| Ptotal | 8.72 | 10.1 | |||||
Note 1 : The supply voltage is measured and specified at the interface connector of LCM.The current draw and power consumption specified is for VDD=3.3V,Test Pattern of power supply current.
Note 2 : The duration of rush current is about 2ms and rising time of Power Input is 1ms(min).
Backlight Electrical Specifications:
| Parameter | Min. | Typ. | Max. | Unit | Remarks | ||
| LED Driver Power Supply Voltage | HVDD | 10.8 | 12 | 12.6 | V | ||
| LED Driver Power Supply Current | IHVDD | 550 | 600 | 700 | mA | ||
EN Control Level | Backlight on | VENH | 3 | 3.3 | 3.6 | V | EN logic high voltage |
| Backlight off | VENL | 0 | 0 | 0.6 | V | EN logic low voltage | |
PWM Control Level | PWM High Level | VPML | 3 | 3.3 | 3.6 | V | |
| PWM Low Level | VPML | 0 | 0 | 0.6 | V | ||
| PWM Control Frequency | F PWM | 0.12 | - | 20 | KHz | Refer to customer comments | |
| Duty Ratio | - | 5 | - | 100 | % | ||
| LED Life-Time | N/A | 50,000 | - | - | Hour | ||
| LED Light Bar Input Voltage Per Input Pin | VPIN | 32.4 | 36 | 39.6 | V | ||
| LED Light Bar Input Current Per Input Pin | IPIN | - | 55 | - | mA | ||
| LED Power Consumption | PBL | - | 7.92 | 8.71 | W | ||
Interface Connection:
| Pin No | Symbol | Description | Pin No | Symbol | Description |
| 1 | VDD | Power Supply, 3.3V(typ.) | 11 | RIN2- | -LVDS differential data input 2 |
| 2 | VDD | Power Supply,3.3V(typ.) | 12 | RIN2+ | +LVDS differential data input 2 |
| 3 | VSS | Ground | 13 | VSS | Ground |
| 4 | NC | No Connection | 14 | CLKIN- | -LVDS differential clock input CLK |
| 5 | RIN0- | -LVDS differential data input 0 | 15 | CLKIN+ | +LVDS differential clock input CLK |
| 6 | RIN0+ | +LVDS differential data input 0 | 16 | VSS | Ground |
| 7 | VSS | Ground | 17 | RIN3- | -LVDS differential data input 3 |
| 8 | RIN1- | -LVDS differential data input 1 | 18 | RIN3+ | +LVDS differential data input 3 |
| 9 | RIN1+ | +LVDS differential data input 1 | 19 | VSS | Ground |
| 10 | VSS | Ground | 20 | NC | No Connection |
Optical Specification:
| Parameter | Symbol | Condition | Min | Typ | Max | Unit | Remark | ||
Viewing Angle | Horizontal | Θ3 | CR > 10 | 85 | 89 | Deg. |
Note 1 | ||
| Θ9 | 85 | 89 | Deg. | ||||||
| Vertical | Θ12 | 85 | 89 | Deg. | |||||
| Θ6 | 85 | 89 | Deg. | ||||||
| Brightness | Lv | Θ = 0. ILED=55m A | 315 | 350 | nit | ||||
| Uniformity | 9 Points | ΔY9 | 75% | 80% | |||||
| Contrast ratio | CR | Θ = 0. | 700:1 | 1000:1 | - | ||||
Reproduction of color | White | Wx |
Θ = 0. (Center) Normal Viewing Angle |
TYP. - 0.03 | 0.313 |
TYP. + 0.03 |
| ||
| Wy | 0.329 | ||||||||
| Red | Rx | 0.649 | |||||||
| Ry | 0.338 | ||||||||
| Green | Gx | 0.323 | |||||||
| Gy | 0.627 | ||||||||
| Blue | Bx | 0.155 | |||||||
| By | 0.056 | ||||||||
| Color Gamut | 67 | 72 | - | % | |||||
| Response Time | Tr+Tf | - | 30 | 35 | ms | ||||
| Gamma Scale | 2.0 | 2.2 | 2.4 | ||||||
Note :
1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o‟clock direction and the vertical or 6, 12 o‟clock direction with respect to the optical axis which is normal to the LCD surface.
Operating Precautions:
1.Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc.
2.Remove the protective film slowly, keeping the removing direction approximate 30-degree not vertical from panel surface, If possible, under ESD control device like ion blower, and the humidity of working room should be kept over 50%RH to reduce the risk of static charge.
