|
[China]
Trade Verify
Address: Foor 2, 4th Buidling, A Zone, Xinhe Xinxing Industrial 3th Zone, Fuhai Avenue, Baoan, Guangdong, China.
Contact name:Catlin Zeng
Shenzhen Wofly Technology Co., Ltd. |
|
Verified Suppliers
|
|
|
Vacuum Measuring Gauge 6000psi Gas Cylinder Regulator Stainless Steel 316
Product Description of Pressure Regulator co2
R41 Serie stainless steel pressure reducers, piston pressure reducing construction, stable output pressure, mainly applied in high input pressure high pure gas, standard gas, corrosive gas and so on.
The General Characteristics of the Range of 6000psi-4000psi Pressure Reducer
| Material | The regulator body should be made of stainless steel to withstand high pressures and ensure durability. |
| Pressure Range | The regulator should be able to handle a high pressure of up to 6000psi and a low pressure of up to 4000psi. |
| Gauge Type | The regulator should have two gauges, one for high pressure and one for low pressure. The high pressure gauge should have a range of 0-6000psi and the low pressure gauge should have a range of 0-4000psi. |
| Thread Type | The inlet and outlet ports should be designed for 1/4 female thread to allow for easy installation and compatibility with other gas system components. |
| Accuracy | The regulator should be able to maintain a consistent and accurate gas pressure output even when there are fluctuations in the input pressure. |
| Flow Rate | The regulator should be able to handle the required flow rate of gas for the application it is being used for. |
| Adjustment Range | The regulator should have an adjustable pressure range that allows for fine-tuning of the gas pressure output. |
| Safety | The regulator should have safety features such as a relief valve to prevent over-pressurization and a built-in shut-off valve to stop the gas flow in case of emergency. |
| Size and Weight | The regulator should be compact and lightweight to allow for easy installation and portability. |
| Technical Parameter | ||
| 1 | Maximum Inlet Pressure | 3000,6000psig |
| 2 | Outlet Pressure Ranges | 0~250, 0~500, 0~1500,0~3000psig |
| 3 | Safety test pressure | 1.5 times maximum inlet pressure |
| 4 | Operating Temperature | -40°F to +165°F / -40°c to 74°c |
| 5 | Leak rate | foam test |
| 6 | Cv value | 0.06 |
Specification
| DESIGN FEATURES OF regulator gas high pressure | |
| 1 | Single-stage reduce structure |
| 2 | Use hard-seal between body and Diaphragm |
| 3 | Body Thread:1/4" NPT (F) |
| 4 | Filter mesh inside |
| 5 | Easy to sweep inside body |
| 6 | Panel mountable or wall mounted |
| Material of stainless steel co2 regulator high pressure | ||
| 1 | Body | 316L.Brass |
| 2 | Bonnet | 316L. Brass |
| 3 | Diafragm | 316L |
| 4 | Strainer | 316L(10 μm) |
| 5 | Seat | PCTFE |
| 6 | Spring | 316L |
| 7 | Plunger valve core | 316L |
| 8 | o-ring | Fluororubber |
| Product Selection of argon /co2 gas pressure regulator | ||||||||
| R41 | L | B | B | D | G | 00 | 00 | P |
| Item | Body Materia | Body Hole | Inlet Pressure | Outlet Pressure | Pressure Gauge | Inlet Size | Outlet Size | Options |
| R41 | L:316 | A | B:6000psig | D:0~3000psig | G:MPa gauge | 00:1/4″NPT(F) | 00:1/4″NPT(F) | P:Panel mounting |
| B:Brass | B | D:3000psig | E:0~1500psig | P:Psig/bar gauge | 00:1/4″NPT(M) | 00:1/4″NPT(M) | ||
| D | F:0~500psig | W:No gauge | 10:1/8″OD | 10:1/8″OD | ||||
| G | G:0~250psig | 11:1/4″OD | 11:1/4″OD | |||||
| J | 12:3/8″OD | 12:3/8″OD | ||||||
| M | 15:6mm”OD | 15:6mm”OD | ||||||
| 16:8mm”OD | 16:8mm”OD | |||||||
| Other type is available | Other type is available | |||||||
Selection of gas
The type of gas that can be regulated using a stainless steel
pressure regulator with a high pressure gauge for 6000psi, low
pressure gauge for 4000psi, and inlet and outlet for 1/4 female
thread depends on the specific model and design of the regulator.
However, in general, stainless steel pressure regulators are
designed to be compatible with a wide range of gases, including but
not limited to:(Compressed air,Oxygen,Nitrogen,Argon,Helium,Hydrogen,Carbon
dioxide,Natural gas,Propane)
Before using a pressure regulator with a specific gas, and customer
service to determine the gas used's specifications and ensure that
the regulator is rated for the specific gas being used. Different
gases may have different pressure requirements and compatibility
requirements, and using a regulator that is not designed for the
specific gas can result in malfunction or safety hazards.
Completion Project
Applicable Scenes
FAQ
1. who are we?
We are based in Guangdong, China, start from 2011,sell to Southeast
Asia(20.00%),Africa(20.00%),Eastern Asia(10.00%),Mid
East(10.00%),Domestic Market(5.00%),South Asia(5.00%),Northern
Europe(5.00%),Central America(5.00%),Western Europe(5.00%),South
America(5.00%),Eastern Europe(5.00%),North America(5.00%). There
are total about 51-100 people in our office.
2. how can we guarantee quality?
Always a pre-production sample before mass production;
Always final Inspection before shipment;
3. what can you buy from us?
pressure regulator,Tube fittings,solenoid valve,Needle valve,check
valve
4. why should you buy from us not from other suppliers?
We have a couple of years with professional engineers and dedicated
technicians.can provide security products for you
5. what services can we provide?
Accepted Delivery Terms: FOB,CIF,EXW；
Accepted Payment Currency:USD,CNY;
Accepted Payment Type: T/T,L/C,Western Union;
Language Spoken:English,Chinese
