Active Member
|
[China]
Address: Fuyong, Baoan ,Shenzhen City,China,
Contact name:Lizzy
SMT LINE EQUIPMENT.CO.LTD |
|
|
AC 220V SMT Line Machine 25W SMT Solder Paste Warm Up Machine
SMT Solder paste warm-up machine CNSMT-TSM801
| SMT Solder paste warm-up machine parameters: |
| Input power: AC100--- AC220V (50HZ), |
| Rated power: 25W |
| Supply equipment air pressure: 0.5MPa(=5bar) |
| Overall dimensions (body size): length×width×height=4500mm×300mm×200mm |
| Equipment weight: 15Kg |
| Time timer: |
| Parameter index data |
| Time adjustment 0.01S---99H99 |
| Working voltage DC 24V |
| Working temperature -10℃～＋50℃ |
| Working environment humidity: 40%～95%, atmospheric pressure: 86Kpa～106 Kpa |
This SMT Solder paste warm-up machine is a special equipment to realize the thawing and temperature recovery of solder paste and red glue. Using the temperature recovery mechanism can better solve the problem of natural temperature recovery, can effectively assist in controlling the production plan, and improve production efficiency; it is very helpful to improve the placement yield.
SMT Solder paste warm-up machine features:
After the mixer is stirred, the viscosity will change, and it
doesn't feel much changed when printed, so many people think it's
okay. However, the solution to the temperature recovery is the
appropriate temperature for the activity of the flux, and there is
a difference between the two.
Of course, the mixing temperature will increase to a certain extent, but it does not reach the required temperature. Also, when you carefully observe the bubbles of chip and bga, you will find that the void ratio is different
Manual
* Please install the air pipe and connect it to AC110/AC220v power
supply,
* First, turn on the power switch of the electrical control, and
adjust the air pressure to 0.4Mpa.
* Put the solder paste in the tank, start the temperature recovery
start button after setting the time, and the temperature recovery
timer starts; the solder paste tank or the red plastic bottle will
automatically sink, and the temperature recovery meeting will be
completed when the set temperature recovery time is reached It pops
up automatically, the red alarm flashes and there is an audible
alarm
Precautions
Please read the following safety precautions carefully for the
operators and maintenance personnel who actually use the placement
machine and its auxiliary equipment (hereinafter referred to as the
machine) to avoid injury during use.
It is possible that part of the content written in the "Safety
Precautions" in this manual does not belong to the specifications
of the products purchased by the user.
In addition, in order to allow you to fully understand the contents of this instruction manual and the warning label of the product, we divide the warning display into the following categories for description. Please fully understand these contents and follow the instructions.
Various marking symbols such as warnings, prohibitions, and instructions are shown below.
Notes on safety
Maintain:
In order to prevent accidents caused by unfamiliarity with the
machine, the repair and adjustment work should be carried out by
maintenance technicians who are familiar with the machine. In
addition, when replacing parts, please use our company's standard
genuine parts. The company is not responsible for any failures
caused by the use of non-standard genuine parts.
The components of the calibrator were adjusted in position before
being shipped from the factory, and then installed. Therefore,
please never try to loosen the fastening screws. After loosening
the screw, the company will not be responsible for the accuracy and
quality of the image to the calibration instrument.
Use environment:
Please use it in the following environment.
Ambient temperature: ＋10℃～＋35℃
Humidity: There should be no condensation below 50% (35℃) and below
90% (20℃).
Surrounding environment: there should be no corrosive gas.
Company Information
CNSMT is the leading manufacturer and supplieir for SMT machines
and Solution with over 10 years' experience in China. And we can
also do OEM&ODM for SMT traders, we have vast of sources in SMT
field,even you need used or new SMT equipments or other parts, we
can help you get the best quality and competitive cost machines.
What we can do for you:
※ We have our own factory make SMT equipments and devices
※ We have a professional technich engineer team for produce
machines
※ We can customize variety of SMT machines for you according your requirements
※ We buy and sell used and new SMT equipments all over the world
※ We provide you SMT full line machines and export to worldwide
※ Becoming the most reliable Chinese partner for you.
FAQ:
1. Are you factory?
Yes, we are factory supplier focus on humidity control for 14 years.
2. Can you email the catalog?
Yes, we can send you by email with whole catalog.
3. How to order online?
Confirm product (quantity, price, payment, shipping etc)---waiting
for email ---confirm order---make initial payment---production
finish---make balance payment---shipping
* click to learn about trade assurance
4. What about the payment way?
30% deposit, balance paid before delivery -- amount > USD5,000
100% deposit -- amount < USD5,000
5. What's the shipping way and timing?
We suggest to ship by sea to get cheapest rate, voyage date to
America around 30~40 days, to Europe 25~30 days, to Asia and
Austrilia 7~15 days. Click here to get exact timing.
10. Which payment terms are you doing?
PayPal, West Union, T/T, (100% payment in advance.)
11. Which shipment is available?
By sea, by air ,by express or as your requirement.
12. Which country you have been exported?
We have been exported to many countries, all most all around the
world, like Malaysia, Vietnam, Thailand, United States, France,
Spain, Mexico, Dubai, Japan, Korea, Germany, Porland Etc.
