|
[China]
Trade Verify
Address: No.755, Xianyuehuan Rd, Tianyuan District, Zhuzhou, Hunan Province
Contact name:Shirley
Zhuzhou Ruideer Metallurgy Equipment Manufacturing Co.,Ltd |
|
Verified Suppliers
|
|
|
400*400*1200-6MPa sinter-HIP furnace with 3 zones temperature independently
Main application
For dewaxing of high-performance cemented carbide material(It can
realize vacuum dewaxing,H2 dewaxing,binder can be paraffin or
PEG),Vacuum sintering,Low pressure Argon dynamic partial pressure
sintering,High pressure Argon sintering,cooling,heat preservation
and heating up under high temperature high pressure status.
General structure
This kind of vacuum pressure sintering furnace for cemented carbide
research, which is single room,horizontal type,recycle heating
furnace,it adopt graphite heating element of low voltage and large
current .It has many heating zone,each heating zone are individual
controlled .All the technical process is automatic
controlled,monitored,chased,fault diagnosed which showed and
recorded by computer.
This Sinter-HIP furnace include control system,heating
system,dewaxing system(vacuum dewaxing and H2 dewaxing),vacuum
system,partial pressure sintering,pressure sintering system,cooling
water system,rapid cooling system,auxiliary system and safety
system etc.It’s graphite box built-in insulation structure,must
keep the best temperature and atmosphere uniformity when sinter
cemented carbide products.Main parts are all international advanced
products,can meet production needs stably and in the long term.At
the same time,it must meet energy conservation and environmental
requirements.
Design standard
Design standard:CE,20-year service life,double doors horizontal
structure,6000 times.
It designed water jacket near furnace door sealing ring,heat
dissipation in time,prolong the service life of the sealing
ring.Designed K-type thermocouple on following positions:front and
rear door,front and rear radiator,front and rear sealing ring,front
and rear chamber,front and rear chamber wall,real time monitoring
temperature at different position,it will alarm when working
temperature over set value,system will safety interlock if it
didn’t remove alarm after long time.
Technical specifications
Basic technical parameter | |
Service life |
6000times / 20-years service life |
Useful space | 400 x 400 x 1200mm |
Max. Loading weight
|
≥300kg(According to Sinter products and loading space) |
Max. Designed temp. |
1600℃(Heating up temperature) |
Max. Working temp. | 1550℃ |
Max. working pressure | 58bar |
Ultimate vacuum degree |
1pa(After heating,cold,empty,dry condition) |
Pumping speed
|
The vacuum degree up to 5 pa within 30min after starting pump,the vacuum degree can get to 3pa after pumping continually within 30min,(after empty sintering,in empty,clean,cold condition) |
Leakage rate (In average 24 h)
|
2pa/h(After testing ultimate vacuum,under empty cold,clean condition,test in average 24h) |
Wax-collection rate
|
≥98% (Ar dewaxing with 10kg wax absolutely, average not more than 3 times ) |
Max. Ramp up rate
|
8℃/min(Room temperature ramp up to 1450℃ in vacuum,empty loaded condition,can be soaked in process when 600℃,1000℃ and 1200℃. ≥5℃/min when Fully loaded |
Pressurized time
|
≤20min Can be set(When Gas source keep around 130bar,pressurized to required pressure) |
Cooling time
| ≤6~7hours( From 1480℃ drop to 100℃ when fully-loaded,water temperature≤28℃ ) |
UPS time
|
Supply power to indicator and to control furnace when power-off, Keeping time≥80min |
Temperature uniformity
|
YG8 or YC40 control inserts to test:Magnetic saturation deviation after debinding ≤±0.25%, Coercivity deviation≤±0.3KA/M |
After sales:
1. Installation, Commissioning And Acceptance
We do installation, commissioning and acceptance in buyer's plant.During the installation and commissioning period, the commissioning personnel shall be provided free of charge by the demander according to the staff standard.
The equipment shipped to the buyer, the seller received the buyer's
notification, both within a week to carry the equipment out of the
box together, then check the equipment and all components according
to the packing list . Including equipment accessories, spare parts
and special tools, attached manual and technical documents, etc. It
can be installed after the acceptance check of equipment.
After installation and debugging, the equipment shall be accepted
according to the technical accessories.
2. Training
When taking-over the Furnace to the customer, We will give a staff
training to customer. The operating personnel of the customer
should join to commission,test the furnace, when installing at
customer’s company.
This is practical operation training and practical maintenance
training,and our technical personnel will telling the basic
principle,equipment maintenance knowledge,And the common fault
handling measures.We can training 2 ~ 3 workers. ( Training how to
maintenance and operating.)
3. Warranty period
The warranty period of the equipment is 12 months, which starts from the date of installation and debugging of the supplier. Equipment failure happens, after-sales service personnel shall give solutions within 2 hours, after receiving the buyer's notification . If it is need to go to the site for treatment , operators dispatched by seller should arrive at the site within 48 hours after go aboard. In case of emergency,operators should arrive at the site within 48 hours after go aboard, and continue to make repairs until the fault is removed and the equipment returns to normal.
