|
[China]
Trade Verify
Address: A-709 Zhengshang International Building, Fengcheng 8 Road,Xi'an,China
Contact name:Shirley
Shaanxi Fortune Industries Co.ltd |
|
Verified Suppliers
|
|
|
TSS60 AS60 NSS60 One Way Freewheels Roller Type Clutch Bearing thickness 22cm
Type AS is a roller type freewheel non-bearing supported. Bearings
are required to support axial and radial loads. Lubrication and
sealing must also be provided by the installation. Nominal outside
dimensions are the same as series 62...Ball bearings.
A typical arrangement is to install this type alongside a series 62
bearing within the same location tolerances, as shown on the
following page. The inner race is keyed to the shaft (except 6 mm
bore).
The outer race has a positive r6 tolerance to give a press fit in a
H7 housing. The outer housing must be
strong enough
To not expand after assembly. This design can accept an axial
misalignment of inner and outer race of ± S/2.
Technical Datas
MODEL | AS60/TSS60/NSS60 | |
TORQUE (Nm) | 508 | |
OVERRUNNING SPEED (rpm) | INNER RACE | 700 |
OUTER RACE | 1100 | |
INNER RACE SIZE (mm) | 60 | |
OUTER RACE SIZE (mm) | 110 | |
THICKNESS (mm) | 22 | |
WEIGHT (Kg) | 0.81 | |
RESISTANCE TORQUE (Ncm) | 26 | |
Dimensions and Capacities
Type | Size |
TKN1) | Overrunning speeds |
| Weight
| Drag torque | ||||||
AS (NSS) | dH7 | nimax2) | namax3) | Dr6 | D5 | L | s | e | f | TR | ||
[mm] | [Nm] | [min-1] | [min-1] | [mm] | [mm] | [mm] | [mm] | [mm] | [mm] | [kg] | [Ncm] | |
6 | 2.1 | 5000 | 7500 | 19 | 15.8 | 6 | 0.3 | 0.6 | 0.3 | 0.01 | 0.18 | |
8 | 3.8 | 4300 | 6500 | 24 | 20 | 8 | 1.3 | 0.6 | 0.6 | 0.02 | 0.24 | |
10 | 6.8 | 3500 | 5200 | 30 | 25.9 | 9 | 1.3 | 0.6 | 0.6 | 0.03 | 0.36 | |
12 | 13 | 3200 | 4800 | 32 | 28 | 10 | 1.3 | 0.6 | 0.6 | 0.04 | 0.48 | |
15 | 14 | 2800 | 4300 | 35 | 31 | 11 | 1.4 | 0.6 | 0.6 | 0.05 | 0.7 | |
20 | 40 | 2200 | 3300 | 487 | 40 | 14 | 2.4 | 0.8 | 0.8 | 0.12 | 1.4 | |
25 | 56 | 1900 | 2900 | 52 | 45.9 | 15 | 2.4 | 0.8 | 0.8 | 0.14 | 2.4 | |
30 | 90 | 1600 | 2400 | 62 | 55 | 16 | 2.4 | 0.8 | 1 | 0.22 | 7.8 | |
35 | 143 | 1300 | 2000 | 72 | 64 | 17 | 2.5 | 0.8 | 1 | 0.31 | 9 | |
40 | 185 | 1200 | 1800 | 80 | 72 | 18 | 2.5 | 0.8 | 1 | 0.39 | 10 | |
45 | 218 | 1000 | 1600 | 85 | 77 | 19 | 2.5 | 1.2 | 1 | 0.44 | 11 | |
50 | 230 | 950 | 1500 | 90 | 82 | 20 | 2.5 | 1.2 | 1 | 0.49 | 13 | |
55 | 308 | 800 | 1300 | 100 | 90 | 21 | 2.5 | 1.2 | 1 | 0.66 | 14 | |
60 | 508 | 700 | 1100 | 110 | 100 | 22 | 2.5 | 1.2 | 1.5 | 0.81 | 26 | |
80 | 1063 | 600 | 900 | 140 | 128 | 26 | 2.5 | 1.2 | 1.5 | 1.41 | 58 | |
NOTES:
AS6 without keyway. ØD = -0-0,009
AS8-12 keyway to DIN 6885.1.
Other sizes to DIN 6885.3
1) T max = 2 × T KN
2) Inner race overruns
3) Outer race overruns
Mounting dimensions are identical to ball bearings series 62
Mounting Example
