GE Line Driver/Receiver Board DS3800HDRA features a modular connector

GE Line Driver/Receiver Board DS3800HDRA features a modular connector

Product Description
The GE Line Driver/Receiver Board DS3800HDRA features a modular connector for attachment to a drive and retention levers to hold the board in the drive. The GE Line Driver/Receiver Board DS3800HDRA also is populated with 2 jumpers, and multiple capacitors. The board also has 2 40-pin connectors accessible from the front of the board.

The 2 40-pin connectors are accessible by the operator when the board is installed in the drive. However, any cables attached to the connectors should only be touched if the drive has all power removed.

Removing power from the drive requires that someone familiar with the installation of the drive confirm that all power has been removed. The drive has multiple sources of current and only someone familiar with the installation will know the sources of power and how to disconnect them. Before you touch the board, use a full featured testing device to confirm that all power is removed.

Be familiar with the emergency power shut off devices associated with the drive. In case of an emergency, the shut offs can remove all power from the drive. It is important that 2 technicians are always present to service the drive. If 1 technician is experiencing an emergency, the other can call for help, shut off the power, or assist the other technician.

Before you start the installation, inspect the area around the drive for safe conditions. Make sure the floor is dry and free of oil and debris. If moisture is on the floor, clean up the water first. If moisture reoccurs, you might have to install dehumidifiers so the floor remains dry.

OTHER SUPERIOR PRODUCTS

 
Similar prodcut for GE

DS3800DDCD181A
DS3800DDCD18IA
DS3800DDCD18LA
DS3800DDCD1BIA
DS3800DDCD1BLA
DS3800DDCDI81A
DS3800DDCDI8IA
DS3800DDCDI8LA
DS3800DDCDIB1A
DS3800DDCDIBIA
DS3800DDCDIBLA
DS3800DDCDL81A
DS3800DDCDL8IA
DS3800DDCDL8LA
DS3800DDCDLB1A
DS3800DDCDLBIA
DS3800DDCDLBLA
DS380ODDCD181A
DS380ODDCD18IA
DS380ODDCD18LA
DS380ODDCD1B1A
DS380ODDCD1BIA
DS380ODDCD1BLA
DS380ODDCDIB1A
DS380ODDCDIBIA
DS380ODDCDIBLA
DS3800DDCD1B1A-A
DS3800DDCD1B1A-B
DS3800DDCD1B1A-C
DS3800DDCD1B1A-D
DS3800DDCD1B1A-E
DS3800DDCD1B1A-F
DS3800DDCD1B1A-G
DS3800DDCD1B1A-H
DS3800DDCD1B1A-I
DS3800DDCD1B1A-J
DS3800DDCD1B1A-K
DS3800DDCD1B1A-L
DS3800DDCD1B1A-M
DS3800DDCD1B1A-N
DS3800DDCD1B1A-O
DS3800DDCD1B1A-P
DS3800DDCD1B1A-Q
DS3800DDCD1B1A-R
DS3800DDCD1B1A-S
DS3800DDCD1B1A-T
DS3800DDCD1B1A-U
DS3800DDCD1B1A-V
DS3800DDCD1B1A-W
DS3800DDCD1B1A-X
DS3800DDCD1B1A-Y
DS3800DDCD1B1A-Z

Product Description

The DS3800DBIB is a small printed circuit board (PCB) designed as part of the Speedtronic (Mark IV) line manufactured by GE. The Speedtronic system is designed to sequence turbine fuel and to sequence turbine systems and their auxiliaries for startup. The Mark IV system is designed with a distributed control system which runs on an array of interconnected microprocessors. When one section of this gridwork fails, turbines will continue to work under the control of other parts of the system. In this way downtime is limited. The DS3800DBIB is designed specifically as an interface board.

The DS3800DBIB is a small daughterboard that works as a plug-in to another, larger PCB. It has been drilled out at the factory, one hole in each corner of the board. This board also has four connectors numbered 1 through 4. It has two small screw mounts covered by black tabs. The first mount is marked C101 and is positioned next to a ring marked TP1. The second is not marked and positioned next to a ring marked TP2. The DS3800DBIB has one capacitor rated 708A1, M/E 200V 1.0 +10%. It also has one blue potentiometer located on the edge of the board that is wired for variable resistance. There are ten resistors and six small capacitors marked 'cr' on the DS3800DBIB PCB

 
Q1. What about the lead time?
A: 3-5 days for Sample preparing ,8-10 working days for mass production.
 
Q2. Do you have any MOQ limit of Industrial Servo Drives?
A: Low MOQ, 1pc is available.
 
Q3. How do you ship the goods and how long does it take to arrive?
A: Ship by DHL, UPS, FedEx or TNT. It takes 3-5 days to arrive. Airline and sea shipping also optional.
 
Secondly, during the guarantee period, we will send new lights with new order for small quantity. For defective batch products, we will repair them and resend them to you or we can discuss the solution including re-call according to real situation.