|
[China]
Trade Verify
Address: 23E BlockB,Lushan Building,Chunfeng Road,Luohu District,Shenzhen,518001,China
Contact name:Mayne
Wisdomlong Technology CO.，LTD |
|
Verified Suppliers
|
|
|
AB 1746-P1 0 to 60 Celsius 47 to 63 Hertz 2 A at 5V dc 0.46 A at
24V dc
Product information AB 1746-P1 :
The AB 1746-P1 is an SLC 500 power supply. It has a line voltage of
85 to 132 Volts or 170 to 265 Volts AC at 47 to 63 Hertz and with a
typical line power requirement of 135 VA. Its internal current
capacity is 2 A at 5 Volts DC and 0.46 A at 24 Volts DC and its
inrush current is a maximum of 20 A. This power supply also has a
24 Volt DC user-power current capacity of 200 mA and a 24 Volt DC
user-power voltage range of 18 to 30 Volts DC.
The maximum user-supplied overcurrent protection is 15 A and the
isolation between the input terminals and the backplane is 1800
Volts AC RMS for 1 second. Measuring 5.5 x 2.3 x 5.7 inches and
weighing 2 pounds or 0.9 kilograms, this power supply can be
installed in a 1746 chassis. It also has an operating temperature
of 0 to 60 degrees Celsius and the current capacity is derated by
5% when the temperature exceeds 55 degrees Celsius.
The input jumper must be set before applying power to the 1746-P1
power supply during installation. This is because the exposed pins
have hazardous voltage when power is applied and this may result in
injury. This power supply comes with fuse protection but this is
limited only to guarding against fire hazards due to short-circuit
conditions. For user-power overcurrent conditions, the 1746-P1
Series A that is made in Japan will undergo a power supply shutdown
and CPU fault and the recovery procedure is to reload the user
program.
For the 1746-P1 Series A that is made in Malaysia, the CPU
continues but a 24 Volts DC user shutdown occurs and the recovery
procedure is to correct the overcurrent condition. When
undervoltage happens, the 1746-P1 power supply will continue to
operate the SLC 500 controllers for a short time and it will stop
supplying power to the controllers when the input voltage drops
below the recommended operating range for a time that is longer
than the CPU hold-up time. For the 1746-P1 power supply, the CPU
hold-up time is 20 ms for the full load and 3000 ms for no load.
Operations will resume once the power supply gets the normal input
voltage.
The 1746-P1 is an SLC 500 Power supply. This Programmable Logic
Component (PLC) is a necessary module to operate an SLC 500 rack.
It provides backplane power which is used by most modules attached
to the chassis to energize each electric circuitry to become
operable.
This power supply module has a line voltage requirement of 85 - 132
/ 170 - 265 VAC with a frequency of 47-63 Hz. Aside from providing
backplane power supply, this module is capable of providing 18-30
VDC voltage with Current of 200 mA. This power supply has an
internal fuse installed which may be replaced with part number of
1746-F1. It also has a user-supplied overcurrent protection rated
15 Amperes.
Through power supplies, SLC 500 controllers are capable of
operating even if the input power supply drops below the operating
voltage level. This feature is known as the CPU hold-up time. The
program and I/O data are continued being scanned for a limited
period. If the power return to normal voltage level, the processor
may continue to operate normally. For 1746-P1, the CPU hold time is
20 ms at full load and 3000 ms at no load.
This power supply is installed at the leftmost of an SLC 500
chassis. Whether main, expansion or Remote I/O rack, the
installation position is same. Only One (1) power supply is needed
per chassis.
More information:
| Backplane Current (24 Volts) | 0.46 Amps |
| Frequency | 47 to 63 Hertz |
| Location | 1746 Chassis |
| Dimensions | 5.5 x 2.3 x 5.7 inches |
| UNSPSC | 32151706 |
| Operating Temperature | 0 to 60 Celsius |
| Fuse Protection | 1746-F1 or equivalent |
| Programming Software | RSLogix 500 |
| IC694MDL230 | 120 VAC Isolated Input (8 Points) |
| IC694MDL231 | 240 VAC Isolated Input (8 Points) |
| IC694MDL240 | 120 VAC Input (16 Points) |
| IC694MDL241 | 24 VAC/VDC Input (16 Points) |
| IC694MDL250 | 120 VAC Isolated Input (16 Points) |
| IC694MDL260 | 120 VAC Input (32 Points)** |
| IC694MDL632 | 125 VDC Input (8 Points) |
| IC694MDL634 | 24 VDC Input, Neg/Pos Logic (8 Points) |
| IC694MDL645 | 24 VDC Input, Neg/Pos Logic (16 Points) |
| IC694MDL646 | 24 VDC Input, Neg/Pos Logic, 1 msec Filter (16 Points) |
| IC694MDL654 | 5/12 VDC (TTL) Input, Neg/Pos Logic, (32 Points) |
| IC694MDL655 | 24 VDC Input, Neg/Pos Logic, 1 ms, (32 Points) |
| IC694MDL660 | 24 VDC Input (32 Points)** |
| IC694ACC300 | Input Simulator Module (8 Points) |
Our brand:
1, First, send us the brand, model code/pic of the nameplate, the quantity for inquiry. Then we will send the quote to you. after confirming the model and the quantity, then we will the PI to you.
2, You can transfer by Paypal/ Western Union/Trade assurance/ T/T. When we received the payment, then we will start to prepare the order for you asap.
