Active Member
|
[China]
Address: 2# Jinlong Rd. Baolong Industrial Zone, Longgang Dist. Shenzhen China 518000
Contact name:Tarik Lu
Force sensor torque transducer |
|
|
Shaft Rotary Torque Sensor 89 in-lb 177lb*in 443lb-in 885 lb-in
1770 lb*in Dynamic Torque Transducer
Shaft to Shaft Dynamic Torque Sensor FY01 is a slip-ring type torque transducer intended for rotating
torque measurement,Slip rings are used to conduct the millivolt
signal from the wheatstone bridge bonded on the sensing shaft which
will rotate together with motor shaft in both clockwise and
counterclockwise direction to get the torque measured. Rotary Torque Transducer FY01 offers 0-89 in-lb / 0-177 in-lb / 0-266 in-lb / 0-443 in-lb /
0-885 in-lb / 0-1770 in-lb / 0-2655 in-lb / 0-4425 in-lb eight
rated measuring ranges with maximum 0.2% non-linearity of the full
scale to choose from. Keyed shafts located on both ends of the
sensor can be connected to motor and load through
couplings.Rotating speed of model FY01 can go up to 4000RPM,it is
also suitable for non-rotating and low-speed torque measurement
applications.Signal conditioner and display unit is also available
to get the readout or 0-5V/0-10V/4-20mA output.Typical applications
for this type of torque transducer are for example servo motor
torque measurement, test bench applications, valve torque test,
torque measurement for stirring devices, screw driver calibration,
twist measurement, actuator test,etc..
Dimensions(unit in "mm")
| Ordering code | Measurement Range | Torque direction |
| FY01-10NM | 0-10Nm | Clockwise & Counterclockwise |
| FY01-20NM | 0-20N*m | |
| FY01-30NM | 0-30N-m | |
| FY01-50NM | 0-50Nm | |
| FY01-100NM | 0-100N*m | |
| FY01-200NM | 0-200Nm | |
| FY01-300NM | 0-300N-m | |
| FY01-500NM | 0-500Nm |
Specifications
| Rated capacity | 10Nm / 1kg*m / 89 lbf-in 20N*m / 2kgf*m / 177 lbf*in 30Nm / 3kgf-m / 266 lbf-in 50Nm / 5kgf*m / 443 lb-in 100N*m / 10kgf*m / 885 in*lb 200Nm / 20kg*m / 1770 lb-in 300Nm / 30kg*m / 2655 lbf-in 500N-m / 50kgf-m / 4425 in*lb | ||
| Rated output | 1.5 mV/V | Compensated temperature | -10...+40oC |
| Excitation | 3-15V | Operating temperature | -20...+60oC |
| Zero balance | ±0.05mV/V | Temperature shift zero | ±0.02% R.O./oC |
| Nonlinearity | ±0.2% R.O. | Temperature shift span | ±0.02% R.O./oC |
| Hysteresis | ±0.2% R.O. | Input resistance | 380±30 ohms |
| Nonrepeatability | ±0.1% R.O. | Output resistance | 352±5 ohms |
| Creep(5min) | ±0.1% R.O. | Insulation resistance | >5000Mohms |
| Safe overload | 150% F.S. | Ingress protection | IP40 |
| Ultimate overload | 200% F.S. | Material of element | Stainless steel |
| Cable | Ø5*3000mm 4-core shielded | ||
| Wiring code | Clockwise@ Red--Power input+ Black--Power input- Green--Signal output+ White--Signal output- | ||
A torque sensor is a transducer that converts a torsional mechanial input into an electrical output signal.Rotary torque sensor is designed to measure rotating torque like motor torque , rotating shaft torque, mixture torque, etc.. Dynamic torque transducer can also be used to measure static torque(which is also known as reaction torque).The output range of rotary torque sensor FY01 is normally within -25mV...+25mV, signal amplification may be required for most applications, a signal conditioner can be used to convert mV signal into -5~5V, 0-10V or 4-20mA output for easy data processing.Taking torque cell FY01-100NM and amplifier FSC(-10-10V)-24V for example,the torque-voltage relationship will be 0-100NM in CW direction VS 0-10V output, 0-100N*m in CCW direction VS 0-(-10V) output, 1V output corresponds to 10Nm torque in clockwise direction, -5V output corresponds to 50N-m torque in anticlockwise direction, and so on.
Shaft Rotary Torque Transducer 89 in-lb 177 lb-in 443 lb*in 885
lb*in 1770 lb-in Dynamic Torque Sensor
