Active Member
|
[China]
Address: 227-11666 DONGTAIHU STREET, SONGLING TOWN, SUZHOU CITY, JIANGSU PROVINCE, P.R.CHINA
Contact name:Vivie Chen
SUZHOU FRANK STEEL CO.,LTD. |
|
|
DIN CuZn37 Common Brass Seamless Tubes For Water Supply Pipe In Washroom
1. Description
DIN CuZn37 is a brass zinc alloy composed of 63% brass and 37%
zinc. This grade brass tube is light in weight, good in thermal
conductivity and with high strength in low temperature . It is
often used to low pressure liquid, manufacture motor vehicle engine, automobile oil pipe, and bathroom water pipe. Small
diameter brass zinc alloy pipe is often used to transport
pressure liquid (such as lubrication system, oil pressure system,
etc.) and equipment pressure pipe.
Brass tube has the following good side: brass tube material is very
hard, difficult to corrosion, in addition, it is also resistant to
high temperature and high pressure, can be used in various
conditions. Compared with other materials, pipes of other materials
have many disadvantages. For example, galvanized steel pipes used
20 years ago, as residential pipes, are very easy to rust. After
using for a period of time, the water will turn yellow and the
water flow will become smaller. In addition, there are some other
materials of the pipe strength will be rapidly reduced at high
temperature, when hot water will produce unsafe risks. But the
melting point of brass is as high as 1083 degrees centigrade, so
the temperature of hot water system is not a problem for brass pipe
at all.
2. Chemical composition
| Cu :62.0～65.0 |
Zn:Remain |
Pb:≤0.08 |
Ni:0.5 |
Fe:≤0.15 |
| Impurity:≤0.5 |
3. Mechanical properties
Tensile strength: (σ B / MPA): ≥ 370
Elongation: (δ 10 /%) ≥ 15
Elongation: (δ 5 /%) ≥ 18
4. Standard comparison
| Category | China | US | UK | Germany | Japan | ||
| GB | ASTM | CDA | BS | DIN | Digital system | JIS | |
| Common Brass | H63 | C27400 | 272 | Cz108 | CuZn37 | 2.0321 | |
5. OD table and tolerance
| T mm OD mm | 0.15--0.2 | 0.2--0.3 | 0.3--0.5 | 0.5--0.8 | 0.8--1.2 | 1.2--1.8 | 1.8--2.5 | 2.5--3 | 3--4 |
| 2.5--5 | √ | √ | √ | ||||||
| 6--10 | √ | √ | √ | √ | √ | ||||
| 11--15 | √ | √ | √ | √ | √ | ||||
| 16--20 | √ | √ | √ | √ | |||||
| 20--25 | √ | √ | √ | √ | √ | ||||
| 25--35 | √ | √ | √ | √ | √ | ||||
| 35--45 | √ | √ | √ | √ | √ | √ | |||
| 45--55 | √ | √ | √ | √ | √ | √ |
| outside diameter | Average tolerance | |
| General (±mm) | high(±mm) | |
| 3--15 | 0.09 | 0.05 |
| 15--25 | 0.1 | 0.06 |
| 25--50 | 0.15 | 0.08 |
6. Wall Thicknese and tolerance
| wall thickness | Average tolerance | |
| General(mm) | high(mm) | |
| 0.2--0.5 | ±0.02--0.05 | ±0.01--0.03 |
| 0.5--0.8 | ±0.05--0.08 | ±0.02--0.05 |
| 0.8--1.5 | ±0.08--0.15 | ±0.05--0.12 |
| 1.5--2.5 | ±0.15--0.25 | ±0.12--0.2 |
| 2.5--4 | ±0.25--4 | ±0.2--0.3 |
7. Details picture
