Active Member
|
Address: JINGUI ROAD 18,YANGSHAN INDUSTRIAL PARK,WUXI CITY, CHINA
Contact name:WANG
FRIENDSHIP MACHINERY CO,LTD |
|
|
Tank Welding Line Turning Roll And Welding Manipulator
Automatic Welding Center
1. Equipment instruction
Welding manipulator can be composed of auto welding mechanical
equipment via welding rotator, welding positioner. It is used for
internal and external circular welding seam, fillet weld and
internal and external
longitudinal welding seam it has functions of moving, rotating,
elevating and traversing.Floor turntable positioner makes the piece
rotating 360 ° in the horizontal direction. It is the tipical
auxiliary equipmentduring the welding process.Automatic welding
center is mainly composed of welding manipulator, floor turntable
positioner and welding source. When working, the fist is to make
piece on the floor turntable positioner and turn welding rotator to
make the work-piece stay to weld by process requirements.Then make
welding torch adjust to a certain welding position through kinds of
movement of welding manipulator. At the last, start welding machine
and rotate work-piece by positioner to realize automatic welding.
2. Technical parameter
Welding positioner
● Load capacity: 2T
● Rotation motor power: 1.1KW
● Tilt motor power: 1.5KW
● Worktable diameter: φ1400mm
● Worktable rotation speed: 0.05-0.5rpm
● Worktable tilt speed: 0.23rpm
● Tilt angle: 0-120 degree
● Table connection form: M20×4 (T type slot)
● Chuck: self centering model
| Model | LH-3030 | LH-3040 | LH-4050 | LH-5060 |
Effective Vertical Lifting Stroke of Boom (mm) | 3000 | 3000 | 4000 | 5000 |
Effective Horizontal Retracting Stroke of Boom (mm) | 3000 | 4000 | 5000 | 6000 |
| Boom Lifting speed (mm/min) | 1 | |||
| Boom Retracting speed (mm/min) | 0.12-1.2 | |||
| Column Rotation Angle (°) | Stationary □ ±180° | |||
| Column Rotation Way (rpm) | Stationary □ Manual □ Motorized(0.1) | |||
| Trolley Traveling Way (mm/min) | Stationary □ Manual □ Motorized(1.5/3) | |||
| Option : | Seam Tracker Flux recovery machine | |||
Welding Source Chinese Lincoln Brand | ||||
3. Performance feature
Welding manipulator is composed of column,boom nose and elevating. Column is rectangle, and on its top
there is boom elevating mechanism which is dual beam. The motor drives worm gear and worm reducer
and drives sprocket and chain. One end of chain is connected with boom guide device, and the other end
is fixed on balance iron in column. There are eight groups of pulley block which is eccentric shaft structur on boom guide seat. Elevating and flexing of boom is controlled by AC variable frequency speed
regulation which can be adjusted according to welding needs. Automatic welding machine head is fixed on
front of the boom, and the nose can be trimming up and down, right and left.The welding positioner is used
typical cradle structure to adapt to the requirements of large tonnage welding. In order to reduce tilt
torque, the middle beam is used U type to reduce the gravity height of work-piece.During the welding
process ground wire must be connected with conductive device. Conductive device connected with table
can make sure of the welding process of form loop. The conductive device is sliding conductive bearing,
with conductive paste. The MAX conductive current can be 1000A.
The complete set of equipment adopts advanced trinity centralized control mode. It means that welding
manipulator welding positioner and functions of welding machine can be fused together organically to
realize welding better. At the same time, it is also equipped with a remote control box which has all
operation functions of this machine to operate conveniently.
USE PIC AND PACKING PIC
 |  |
 |  |
 |  |
