|
[China]
Trade Verify
Address: No.138 Ningkang West Road, Yuecheng, Yueqing,Zhejiang,325600,China
Contact name:Ye
Zhejiang Dopow Technology Co.,Ltd |
|
Verified Suppliers
|
|
|
Standard Cylinder SC Series 70Kgf PT1/8 Pneumatic Air Cylinder
| Model | Bore size |
Port size | Standard stroke mm | Max.theoretical force | Piston port size | Available accessories | Mode | Maxoperating pressure |
| SC32 | 32 | PT1/8 | 25 〜500 | 70Kgf | M10X1.25 | FA |
SC-S:With magnet SCD:Double rod SCJ:Double rod adjustable SAC:Front spring STC:Rear spring | 0-10/kgf/cm2 |
| SC40 | 40 | PT1/4 | 25-800 | 110Kgf | M12X1.25 | |||
| SC50 | 50 | PT1/4 | 25〜1000 | 170Kgf | M16X1.5 | |||
| SC63 | 63 | PT3/8 | 25-1000 | 280Kgf | M16X1.5 | |||
| SC80 | BO | PT3/8 | 25〜1000 | 450Kgf | M20X1.5 | |||
| SC100 | 100 | PT1/2 | 25〜1000 | 700Kgf | M20X1.5 | |||
| SC125 | 125 | PT1/2 | 25-1000 | 1050Kgf | M27X2 | FB-rear flange CA-single clevis CB-double clevis LB-fbot bracket "joint l-l joint TC-center trunnion | ||
| SC160 | 160 | PT1/2 | 25〜1000 | 1800Kgf | M36X2 | |||
| SC200 | 200 | PT1/2 | 25~1000 | 2827Kgf | M36X2 | |||
| SC250 | 250 | PT1/2 | 25-1000 | 4400Kgf | M42X2 | |||
| SC320 | 320 | PT3/4 | 25〜1000 | 7238Kgf | M48X2 |
Delivery
1. If the products we have in stock, we will send it out ASAP after
payment.
2. If the products which were customized, we will complete the
production within a specified period of time, and send it out the
first time, we can promise it.
3. Also we can send by your delivery acount if you want.
4. We have a variety of ways to send goods, usually DHL, Fedex, TNT
will be normal ways. If you require use of a courier, we can do it.
MGPM12 Series Replace SMC MGP Compact Guide Cylinder
Caution
1. The compatibility of the product is the responsibility of the
person who designs the equipment or decides its specifications.
Since the product specified here is used under various operating
conditions, its compatibility with specific equipment must be
decided by the person who designs the equipment or decides its
specifications based on necessary analysis and test results. The
expected performance and safety assurance of the equipment will be
the responsibility of the person who has determined its
compatibility with the product. This person should also
continuously review all specifications of the product referring to
its latest catalog information, with a view to giving due
consideration to any possibility of equipment failure when
configuring the equipment.
2. Use cylinders within the piston speed range.
An orifi ce is set for this cylinder, but the piston speed may
exceed the operating range if the speed controller is not used. If
the cylinder is used outside the operating speed range, it may
cause damage to the cylinder and shorten the service life. Adjust
the speed by installing the speed controller and use the cylinder
within the limited range.
3. Pay attention to the operating speed when the product is mounted
vertically.
When using the product in the vertical direction, if the load
factor is large, the operating speed can be faster than the control
speed of the speed controller (i.e. quick extension). In such
cases, it is recommended to use a dual speed controller.
