|
[China]
Trade Verify
Address: 608, Building B, Yinyi Duhui Guoji, No.8, Lane 559, Youngor Avenue, Haishu District, Ningbo, China
Contact name:Brandon Bao
Ningbo Brando Hardware Co., Ltd |
|
Verified Suppliers
|
|
|
Airtac 2V025 Series 2V025 - 08 Aluminum Pneumatic Solenoid Valve Direct Acting Normally Closed with Port Size 1 / 4 "
Solenoid valve 2V025-08 features:
1, Direct acting and normally closed type 2/2 way solenoid valve. Its high sensitivity allows it to change direction quickly.
2, The structure is small and compact
3, The valve body is made of brass which is heat resistance and the coil conforms to Class B classifications. The seals are made of fluorine rubber (VITON) which is suitable for several types of working medium.
Instruction of Ordering Code:
2V 025 - 08
1, 2V is sepcification code, stand for 2/2 way solenoid valve
2, 025 stand for flow orifice: 2.5mm
3, 08 stand for port size for connecting pipe, 08 means 1/4", 06 means 1/8"
2V025 Two-Way Solenoid Valve Specifications:
| Valve Model | 2V025-06 | 2V025-08 |
| Valve Type | 2Way,Normally Closed(NC) | |
| Action | Direct Acting(Poppet); Fast Response Time:<20msec | |
| Orifice(Cv) | 2.5mm(0.23); 22SCFM@100psi | |
| Operating Pressure | Vacuum to 115psi | |
| Operating Temperature | -4 to 140°F(-20 to 60°C) | |
| Port Size (Tube OD) | 1/8”NPT | 1/4”NPT |
| Wetted Surfaces | Valve Body:Anodized Aluminum Seals:NBR(Buna N) Armature Assembly:Brass;Option:Stainless Steel | |
| Coil Duty | F Class,IP65,100% ED(Continuous Duty) | |
| Voltage | Options:12,24 VDC;24,110/120(50/60Hz),220/240 VAC(50/60Hz) | |
| Voltage Tolerance | 110% of Specified voltage | |
| Coil Power | 3to 6.5W(pressure dependent) | |
| Electrical Connections | DIN 43650 Form A or Grommet | |
| Installation | No Orientation Requirement(Optimum Position:Flow Horizontal & SolenoidVertical) | |
| Service | Air,Liquid,Vacuum | |
2V025 Series Solenoid Valve Components:
| Number | Part Name | Material or Specification |
| A | Nut | M8X0.75 |
| B | Grommet wires | / |
| C | Encapsulated solenoid coil | enamelled copper wire |
| D | Compression plate | stainless steel |
| E | Screws | M3X0.5X5mm |
| F | Armature tube assembly | brass, option: stainless steel |
| G | Spring | stainless steel |
| H | O-ring | NBR |
| I | Plunger | Stainless steel |
| J | Valve body | Anodized aluminum |
Our Product 2V025-08 Advantages:
1, High working frequency and high quality armature assembly.
Frequency: minimum 5 time per second, working well and smart respond
2, Key important parts easily assemble or dis-assemble:
3, Adopting high quality copper wire (not aluminum wire) to make the solenoid coil:
4, Smooth valve body surface, no any bur in the inner surface or thread:
Solenoid Valve 2V025-08 Overall Dimensions:
Installation & Operation of 2V025-08:
To Connect the Valve Inlet & Outlet:
Connect the inlet & outlet to the valve ports according to the
flow direction arrow marked on the valve
To Install the Coil:
Put the coils on to the armature tube of the valve. Place the lock
washer & nut on to the armature tube. Hand tighten the nut,
then use a wrench to tighten the nut another quarter-turn.
Do not over-tighten the nut, as it may cause the armature tube to
fail prematurely.
To Connect a DIN Coil:
1. Remove the screw from the plastic DIN housing & unplug it
from the DIN coil
2. From the screw opening, push the terminal block out from the
plastic DIN housing.
3. Note the “1”, “2”, and ground “⏚” symbols on the underside of
the DIN enclosure.
4. For DC DIN Coils, connect “1” to your Positive Lead & “2” to
your Negative lead.
5. For AC DIN Coils, connect “1” to your HOT lead, “2” to your
Neutral lead, & “⏚” to your ground if required.
Do not energize the coil without installing it onto the valve or
connect the coil to a different voltage than specified. This will
burn the coil and could create fire hazards.
Safety Note: Standard valves are supplied with continuous duty coils. The
proper class of insulation for the service is indicated on the coil
body. The coil temperature may rise significantly if energized for
extended periods—this is normal. Although the coil is made of
flame-retardant material, misuse of the coil could create fire
hazards & generate smoke and/or a burning odor. If these
conditions are encountered, the coil temperature has risen above
safe levels and the power should be disconnected immediately.
Operation: This valve is a two-way, normally closed, direct-acting valve
& does not require a minimum differential pressure to operate.
As shown in the diagrams below, when the coil is de-energized (left
diagram), the plunger rests on the main orifice & is held in
place by the plunger spring force, sealing the valve. When the coil
is energized (right diagram), the solenoid lifts the plunger &
allows the working medium to flow through the orifice. The working
medium & flow direction are indicated in purple in the diagrams
