|
[China]
Trade Verify
Address: 608, Building B, Yinyi Duhui Guoji, No.8, Lane 559, Youngor Avenue, Haishu District, Ningbo, China
Contact name:Brandon Bao
Ningbo Brando Hardware Co., Ltd |
|
Verified Suppliers
|
|
|
G1 1/2'' DN40 2W400-40 Solenoid Valve Automatic Water Flow Control 100% Brass Material Body
2W series brass water solenoid valve, the valve body is made of brass forging, the coil is made of pure copper, used for automatic control of liquid and gas medium on and off in the pipeline. The solenoid water valve is controlled by the electromagnetic effect, and is a valve that uses an electromagnet to manipulate the movement of the spool. It is a two way piloted solenoid valves, maximum pressure to make pressure: 17kgf / cm2. Ambient temperature: 0 ° C ~ 65 ° C. The product series production, small volume, large flow, wide application range, according to the flow arrow on the valve, can be installed arbitrarily; in order to enhance the service life, it is best to install the coil horizontally.
Technical data of DN40 solenoid water valve for automatic control:
| Model | 2W025-06 | 2W025-08 | 2W040-10 | 2W160-10 | 2w160-15 | 2W200-20 | 2W250-25 | 2W350-35 | 2w400-40 | 2W500-50 |
| Working medium | Air,Water,Gas,Oil | |||||||||
| Action pattern | Direct type | |||||||||
| Aperture of flow rate | 2.5 | 4 | 16 | 20 | 25 | 35 | 40 | 50 | ||
| Working fluid viscosity | 20 cst below | |||||||||
| Temperature range | -5-85℃ | |||||||||
| Material of seals | NBR,EPDM or VITON | |||||||||
Schematic diagram of Armature for G1-1/2'' 2W400-40 pneumatic water solenoid valve:
Structural disassembly diagram of 2W400-40 100% brass body water solenoid valve:
Application environment of 24VDC/220VAC 2W400-40 water electromagnetic valve:
The installation of water solenoid valve should pay attention to the following points:
1. Before installing the solenoid valve with water solenoid valve, the pipeline must be cleaned. It is recommended to install a filter in front of the valve and a steam pipe to install the trap.
2. When installing, the solenoid valve coil is upward and maintains
the vertical position. The arrow or mark on the solenoid valve
should be consistent with the flow direction of the pipe, and
should not be installed in places with splashing water or water
leakage.
3. The working medium of the solenoid valve should be clean and
free of particulate impurities. The dirt and filter on the surface
of the solenoid valve internal parts should be cleaned regularly.
4. In the pipeline system, the diameter of the solenoid valve
installed on the branch road should be smaller than the diameter of
the main pipeline valve.
5. The electromagnetic water valve cannot be used in explosion
hazardous situations.
6. The valve cannot be installed in the low recess of the pipeline
to prevent the condensation of steam, impurities and the like from
being deposited in the valve.
7. Before using the solenoid valve for water, pay attention to the
product label and read the instruction manual carefully to judge
whether the product meets the conditions of use.
8. Water solenoid valve In the case of insufficient rigidity of the
pipeline, it is recommended to fix the front pipe of the valve with
a bracket to avoid vibration caused by the solenoid valve working.
9. When the solenoid valve is faulty, in order to isolate the
solenoid valve in time and ensure the normal operation of the
system, it is better to install a bypass device.
10. A pressure gauge should be installed on the pipeline before and
after the water solenoid valve to observe the pipeline pressure.
Welcome to your enquiry!
