Active Member
|
[China]
Address: No. 28 Datong Road, Xuguan Town, Suzhou New District, P. R. China, Suzhou, Jiangsu, China
Contact name:Kaisa
Bohyar Engineering Material Technology(Suzhou)Co., Ltd |
|
|
Light Weight Stainless Steel Trav L Cutter 5Mm - 20Mm Wall Thickness
Trav-L-Cutter, or "Travel Cutter," is a portable pipeline cutting,
beveling and milling machine with 6in-72in capacity. This machine
features atmospheric anti-corrosion package with stainless steel
components and special finishes.
The Model TC0672 utilizes a powerful, sealed closed loop hydraulic
drive system, includes anti-corrosion package with stainless steel
components and special finishes. It is ideally suited for hostile
environments or for use underwater.
■ Perfect cold cutting
It has been used in a wide range of applications, including natural
gas, crude oil and radioactive environments
■ Compact & portable design
Light weight, only 10"-12"gap, less than 10 minutes to install
■ A wide range of applications
Operate in the trenches full of silt and 25 meters underwater and
available for cutting and beveling in flooded trenches and
underwater mud at 600 feet.
■ Good stability
Strong corrosion resistance and durable structure
Tools
Model | TC0672 | Processing Range | 6"-72"(153mm-1829mm) |
Drive | Hydraulic | Wall Thickness | 5mm-25mm |
Hydraulic Requirements | 15 gpm @ 1500 psi. | Clearance | 254-305 mm (10"-12") radial, depending on pipe diameter. 20"axial(508 mm) |
Feed Method | Positive, non-slip chain drive. | Finish | Paint |
Cutter Speed | Adjustable 0-60RPM | Installation | Vertical or horizontal installation |
Operating Dimension | 610x510x280(mm) | Operating Weight | 100kg |
Hydraulic Control | Cutter on-off, feed on-off. Flow control valves which can adjust feed speed. Separate controls, providing adjustable feed and cutter speed. Forward/Reverse travel permits machine to be backed up. | ||
■ We have standard beveling tools of 30°, 37° and also can customize
the tools.
■ Connect the hydraulic hose to the valve block on the Travel
Cutter.
■ With the hydraulic supply turned on the machine is ready to cut
the pipe. Turn the valve handle on cutter valve 90° to the right.
This will make the cutter spindle motor in operation and rotate the
cutter.
■ Slowly feed the rotating cutter down until it extends through the
wall of the pipe by approximately 14mm(A maximum single cutting
depth is 14mm and it will affect the use efficiency if exceeding
14mm) This is done by turning the feed screw in a clockwise
direction. One complete turn of the feed screw lowers the cutter
4mm. Lock the cutter in position by placing the feed screw lock on
the shoulder of the feed screw and lock in place with the thumb
screw.
■ Turn valve handle on feed valve 45° to the right. This will
operate the drive motor and make the machine travel around the pipe
for a complete cut. Speed may be reduced by adjustment of the feed
valve handle (close slowly until proper speed is attained). Machine
is traveling too fast if wheel to right of cutter lifts off pipe or
if machine is vibrating excessively.
■ When the cut is completed, stop the drive motor by turning feed
valve to the left until machine stops. With the cutter still
rotating release the elevating screw lock and raise the valve to
the left 90°. Remove the cutter from the machine. Release the
tension on the drive chain by turning the chain tension screw
counter clockwise. Remove the connecting pins from the chain to
uncouple it and the machine can be removed from the pipe.
Maintenance Information: Before the machine or any of its accessories is returned for maintenance, please call Bohyar Company. We will give suggestions on transportation and handover of the machine or accessories, and estimate the time and cost of corresponding maintenance.
