Jiangsu Olymspan Thermal Energy Equipment Co.,Ltd |
|
RHCM highlights a hot mould temperature control machine
Rapid lifting die temperature technology
The deficiency of traditional injection mold temperature control is
as follows
Can't meet highlights the needs of the rapid heating and fast
cooling of injection molding.
Warming to smaller, dissolves mark on the surface of the products
can only ease to eliminate.
Because the plastic hardness is higher, more illiquid.So using this technology, hardness on the surface of the products
can only achieve HB level, unable to meet the needs of the actual
use.
Thermal expansion when mould temperature, cooling will shrink
again, when the clamping force is very unstable.
Easy to cause products play discontent, burning, large internal
stress and other defects.
The mould configuration
Die surface requires a very high degree of finish, to ensure that
the products surface quality.
Mold internal open pipe must be reasonable, to ensure that can
quickly heat up and cool down.
Die internal pipelines should be heat conduction performance is
good.
Due to production needs to constantly in the process of heating and
cooling, mould is better selection of steel.
Uniform structure, small heat bilges cold shrink coefficient.
In use process should especially pay attention to the maintenance
of the mold, to ensure that the dry and clean.
GWS applications
Mould temperature control machine advantages highlights a hot water
Eliminate product surface wiring, dissolves mark, corrugated,
silking of silver.
Completely solve the surface of the plastic product shrinkage
phenomenon.
Improve the product surface finish, make the surface finish can
achieve the mirror.
Product does not need to paint the follow-up processing, increase
yield 20-30%.
Resolving the floating and woven products to jilt woven phenomenon
make the quality more perfect.
To improve thin-wall molding by injection of liquidity, improve
product quality and strength.
The thick wall injection molding cycle can reduce more than 60%,
reinforced plastics fluidity and filling effect.
95% of heat recovery.
100% of the dielectric recovery.
Don't need to connect the boiler and other external auxiliary
equipment temperature control, omitting complex boiler equipment
(high pressure equipment safety and environmental protection for
examination and approval) and pipeline projects.
Completely solve the boiler steam recycling, energy consumption of
big problem.
Xiaoke mobile at any time and the machine use different volume, 180
℃ hot water completely take the place of boiler not environmental
protection.
Highlights a hot mould temperature control machine characteristics
A 10.4 -inch LCD panel LCD display (optional), touch mode in
Chinese digital input, all Chinese interface, easy to operate.
Full closed-loop system control input/output temperature detection,
to mold actual temperature feedback PLC, number, according to the
colour change to ensure accurate output stability.
High temperature hot water and cold water, air temperature and
pressure six alarm, the time and temperature movements and the
injection molding machine signal interlock.
The Europe and the United States imports of components.
Mold temperature detection (optional), single and double road input
and output pipeline adopts 316 stainless steel tube, multiple sets
of input and output interface.
The machine is equipped with;Heating, cooling, cold and hot conversion control function.
High temperature hot water, cooling water recycling system, energy
saving effect is obvious.
Highlights a hot mould temperature control machine application
At present in home appliance, automotive, communications, daily
necessities, medical equipment and other industries have extensive
application prospect, such as LCD TV, computer liquid crystal
displays, notebook computers, mobile phones, air conditioning, car
LCD monitor, car inner decoration, light and optics, OA and AV
instruments, etc.
Specification | |||
Model | Unit | GWS-800 | GWS-1600 |
Power | V | 3∮380V/50HZ | |
Total power | KW | 114 | 157 |
Control mode |
| Computer PLC processor + HMI touch control | |
electro-thermal power | KW | 45-108 | 60-150 |
Heat pump power | S | 2.8 | 2.8 |
Cooling pump power | KW | 2.2 | 3.0 |
DN of hot water and cold water circulating | Inch | DN25(3/8x12) | DN32(3/8x16) |
Cold water circula | Inch | DN32 | DN40 |
Size | MM | 1700x850x1400 | 1900x900x1600 |
Weight | Kg | 700 | 900 |