Active Member
|
[China]
Address: Room 617, Guanlida Building, NO. 269 of Qianjin Road, Wenhui community, Xin'an street
Contact name:Frank
Shenzhen zk electric technology limited company |
|
|
The PV100 IP65 water proof and dust proof series solar pump inverter is a green energy products with new solar MPPT technology, which developed based on general frequency inverter ( or VFD), focusing on driving 1/3 phase AC pumps including AC induction pumps or high efficiency pumps with permanent magnet synchronous motor (PMSM) technology.
Compare to on grid or off grid solar inverter, it has soft starter, and multiple functions of motor protection, and very high competitive price.
An arrays of solar panels generates the power and voltage required for the PV100 solar pump inverter to drive the AC pumps. The solar pump inverter converts the DC voltage input to a 3-phase AC output with variable voltage and frequency. The MPPT algorithm of solar inverter extracts maximum power available from the solar panels during the day and operates the motor at variable speed based on the power input to the inverter. The frequency range in which the inverter operates depends upon the motor speed, hydraulic system and the power available from the solar panel. As the sunshine varies during the day, power input to the inverter varies and the solar pump inverter generates variable V/F ratio thus controlling the speed of the motor, which in turn regulates the pump impeller speed. Water Level Sensor is used only when the water is pumped to overhead tank.
Models list:
Model | Input voltage | Output for pumps | Power | Szie (cm) |
PV100-2S-2.2 | 100 to 450VDC, or 220VAC | 3 PH 0-220VAC | 0.4kw/0.75kw/1.5kw/2.2kw | 272*130*178 |
Solar pump system features
High flow system for faster tank fill and significant water output with MPPT function.
·Proven motor and pump technology for long-term reliability
·Available free of cost at your doorstep, one times investment for more than 20 years free using
·Clean and pollution free energy, eco-friendly.
·Ideal for remote areas, where electricity is not available or availability is capital intensive.
·Suitable for day time irrigation, continuous supply for 8-12 hours in a day.
·Soft start feature prevents water hammer and increases system life easy to operate.
·Simple installation and maintenance free.
Produst Features
Suitable for driving all 1/3 phase induction AC pumps, for PMSM high speed pumps is option.
Multiple control modes, local control, auto start/stop, GPRS remote control.
Maximum power point tracking (MPPT) with fast response speed and stable operation
Dry run (under load ) protection, Water tank fulling detect, Maximum current of pump protection
Low stop frequency protection, sleep/ wake up function when lack/enough of sunlight radiation.
Dual mode input, compatible with DC and AC power input, low and wide range voltage input.
The PQ (Power/Flow) performance curve enables calculating the flow output from the pump
Multiple pumps protection function, short circuit, phase missing, over current, over voltage...
Ambient temperature
IP65 special design good for water proof and dust proo
PV100 solar pump inverter Power switch and wiring:
PV100 solar pump inverter special solar pump control parameters list
HF Solar pump control protection function | |||
HF.00 | Sleep voltage threshold | Setting range: Under voltage setting ～H9.23, when the DC bus voltage lower than this setting value, it will appear E060 alarm( Low voltage alarm) | 150/260V |
HF.01 | Wake up voltage threshold | Setting range:HF.00 ~ 1000 When the DC bus voltage higher than this value or equal to this value for HF.02 delay time, the E060 alarm will be disappeared in sleep mode | 240/360V |
HF.02 | Awake waiting time | 0.0～1000S | 120s |
HF.03 | Stop frequency when low speed ( lowest frequency ) | Setting range:0.0 ～ P0.04 When the output frequency is lower than this setting value for a HF.04 lasting time, it will appear E055 alarm . 0.0Hz means there are no lowest stop frequency protection. Once it is started, the timing will be activated. The timing will be reset once the output frequency higher than this value within set time. As long as the output frequency is lower than this value, re-timing again. | 20.0Hz |
HF.04 | Low frequency protection detection time | Setting range: 0.0 ～ 3600S | 60.0s |
HF.05 | Low stop frequency protection reset delay time | Setting range: 0.0 ～ 3600S Reset time, it will be timing when E055 protection is activated | 120.0s |
HF.06 | Dry run protection current threshold ( under-load protection )
| Setting: 0.0 ～100.0% (100.0% corresponding to P2.06 setting) When the output current is lower than this set value for a detecting time HF0.7, the dry run function will be activated, and submit E056 alarm. 0.0A means no operation Once it is started, the timing will be activated. The timing will be reset once the output frequency higher than this value within set time. As long as the output frequency is lower than this value, re-timing again. | 0.0% |
HF.07 | Dry run protection detecting time | Setting range: 0.0 ～1000S | 60s |
HF.08 | Dry run reset relay time
| Setting: 0.0 ～ 6000S Reset time, it will be timing when E056 protection is activated | 120s |
HF.09 | Over load of pumps protection setting | Range:0.0 ~ 2 times * P2.06 If the output current is higher this setting for longer HF10 setting time, it will show E065 alarm. | 140% |
HF.10 | Over load detecting time | Range: 0.0 ~ 1000S | 60 |
HF.11 | Over load restore time | Range:0~ 1000S Restore time calculte from E065 appears, and it will be reset after tis restore time. | 120 |
HF.12 | Minimum power input protection threshold | Setting range: 0~ 100.0KW The minimum power input protection will be activated when output power is lower than this value for a detecting time HF.13, and show E070. | 0.0 |
HF.13 | Minimum power input detect delay time | Setting range: 0.0 ~ 1000S | 60 |
HF.14 | Automatic recovery time in minimum power input protection mode | Setting range:0.0 ~ 1000S Reset time,timing when E070 is be activated.
| 120. |
