|
[China]
Trade Verify
Address: 101-1101, Building 17, Dianda Guyuan Industrial Park, Mashantou Community, Matan Street, Guangming District, Shenzhen
Contact name:June Zhao
Shenzhen Merrytek Technology Co., Ltd. |
|
Verified Suppliers
|
|
|
LED linear drivers DALI2 dimmable with up to 70W with multiple output current from 700mA to 1400mA
【Product Feature】
【Parameter】
Input | Operating Voltage | 198-264Vac 50Hz /60Hz |
| Rated Input Voltage | 220-240Vac 50Hz /60Hz | |
| DC Input Voltage range | 200-240Vdc | |
| Input Current | 0.23A Max. | |
| Input Inrush Current | <15A (Half current pulse width100μs) @230Vac | |
| Power factor | ≥ 0.95 (@230Vac,100% load) | |
Total harmonic distortion Typical:(@230Vac, 100% load) | 50C-3 | |
| 13% | ||
| Stand-by power | ≤0.5W (@230Vac when PUSH or DALI turn off) | |
Efficiency Max(@230Vac,100% load) |
87% | |
| Wiring Method | Push terminal, wire cross section:0.5-1.5mm2 | |
Output | Operating mode | Constant Current |
| Load type | LED | |
Ripple requirement (Flickering or lickering-Free) | Flicker value: less than 2% for whole dimming range | |
| Start up time | <1s (@230Vac,) | |
| No-load output voltage:DC Max. | 75V | |
| Load output voltage range | 9-66 | |
| Full load output power | 70W | |
| Load output current | Query dial setting table | |
Constant current/voltage Precision | Constant Current Precision ±5% | |
| Wiring method | Push terminal, wire cross section:0.5-1.5mm2 | |
Control Method | Primary PUSH Dimming | Primary PUSH dimming (Max.lead length:20M) |
| 1-10V(0-10V)Dimming | 1-10V dimming(Port current＜1MA) no turn off function (Max.lead length:20M) | |
Dimming Range | Primary PUSH & DALI dimming: 0%-100% 1-10V dimming: 2%-100% | |
| Primary PWM Dimming | 1-10V port PWM dimming (3KHZ-8KHZ) | |
| Potentiometer | Yes, 100kΩ | |
| DALI Dimming | DALI dimming (Max.lead length:300M) | |
Exception Protection Requirements | Output over temperature protection | Yes, without self recovery function(Can be inquired) |
| Output short circuit protection | Yes, without self recovery function(Can be inquired) | |
Operating Environment | Operating temperature/ humidity | -25℃~50℃ Humidity:85% (Non-condensing) |
| Storage temperature/ humidity | -40℃~80℃, Humidity:10%–95% | |
| Max. case temp(Tc) | 85℃ | |
Safety & EMC | EMC standard | EN55015 EN61547 EN61000-3-2 EN61000-3-3 |
| DALI protocol standard | IEC62386-102, IEC62386-207 DT6 | |
| Safety standard | EN61347-1 EN61347-2-13 | |
| Certification | CE RoHS | |
| Withstand voltage | 3750Vac, 5mA, 60s (Input “L N”- Output “SEC”) | |
Others | Degrees of protection | IP20 |
| Type of protection | Class I | |
| Installation type | Independent installation | |
| Installation dimension | 284*30*20.5mm | |
| Blackout memory function | Yes, PUSH blackout memory | |
| PUSH dimming synchronization | 20 units Max. | |
| Packaging requirement | Instruction+clapboard+outer carton(K=A) | |
| Weight | 225g | |
| Life | 50000h @Ta full load | |
Note: All parameters are tested at the input voltage of 230Vac and 25 degree environment unless specified. | ||
【Dimension (Unit:mm)】
【Wiring Diagram】
Fig. A DALI Dimming
Fig. B Push Dimming
Fig.C 1-10V Dimming
【Derating】
【Dimming curve】
【Current gear setting】
KL70C-PDiiV1 Current gear setting | 1 | 2 | 3 | 4 |
| 700(9-66V) | - | - | - | - |
| 800(9-66V) | ON | - | - | - |
| 850(9-66V) | - | ON | - | - |
| 900(9-66V) | - | - | ON | - |
| 950(9-66V) | ON | ON | - | - |
| 1000(9-66V) | ON | - | ON | - |
| 1050(9-66V) | - | ON | ON | - |
| 1100(9-63V) | - | ON | - | ON |
| 1150(9-61V) | ON | ON | ON | - |
| 1200(9-58V) | ON | ON | - | ON |
| 1250(9-56V) | ON | - | ON | ON |
| 1300(9-54V) | - | ON | ON | ON |
| 1400(9-50V) | ON | ON | ON | ON |
【ON/OFF & Description of Dimming Operation】
A. Short press the PUSH switch (short press time 0.1S-1S), the LED driver will turn on or off.
B. Dimming: Press and hold the PUSH switch (1S-8S), the LED driver can achieve dimming, brightening or dimming, the dimming range is 2-100%.
C. Memory: PUSH dimming has dimming memory function.
D. Dimming synchronization: The power connected to the same PUSH switch can be synchronized by pressing and holding the PUSH switch for longer than 15S
E. DALI dimming mode: Connect the power supply to the DALI system, and it can be dimmed by the DALI host. The dimming range is 0-100%.
【Attention】
1) The LED string must be connected to the load before turning on the input power, otherwise the LED string may be damaged.
2) After the LED drive input is powered off, there will be a residual voltage at the output, which can be maintained for about 3 minutes.
