|
[China]
Trade Verify
Address: Huadu District, Guangzhou City, Guangdong Province, China
Contact name:ZENG
YUEMI |
|
Verified Suppliers
|
|
|
Type:Suit for Grundfos CM series pumps
Replacement: AES SOS
Temperature:-20℃ to +180℃
Pressure:≤1.2Mpa
Speed:≤10m/s
Material: A.B,Q1,Q2,P,E,V,F,G
This Seal has two kinds of stationary, one is round, it is GR-G11
Another is elliplic, it Is GR-G11-E
P (mm) | D1 | D3 | T |
| 12 | 22.5 | 48 | 23.6 |
| 16 | 27.0 | 48 | 23.6 |
| Suit for Grundfoss CM series pumps ,Replacement:AES SOS | |
| Temperature:-20ºC to 200ºC, dependent on the elastomer Pressure:Up to 25 bar Speed:Up to 20 m/s Shaft size: 12mm.16mm | Material: Face:Carbon, SiC, TC Seat:SIC, TC O-rings:NBR, EPDM, VITON, Aflas, Kalrez, Chemraz etc. Spring: SS304, SS316 Metal parts: SS304, SS316 |
| This Seal has two kinds of stationary, one is round, it is
GR-G11,Another is elliplic, it is GR-G11-E. Shaft Size 12mm Cartridge Mechanical Seal For Horizontal Pump CM1 CM3 CM5 Shaft Size 16mm Cartridge Mechanical Seal For Horizontal Pump CM10 CM15 CM25 Pump to replace AES SOS Glf Cartridge Mechanical Seal for Pump Arie-Aqqe CM 12 CM 16 for GrundfosS CM CME CMV Pump CM1 CM3 CM5 Grundfoss pumps: JP Ch8 Ch12 CRK (I) 2 CRK (I) 4 SPK1 SPK2 SPK4 SPK8 Cr2 Cr4 AQQE AQQV 96932392 | |
Preperation:
1. Shaft Outside Diameter is within tolerance +-0.05mm
2. Shaft run out <0.1mm
3. Shaf end float <0.13mm
4, No sharp edges on the shaft over the o ring
Note:
During the installation,don't scratch or damage the o ring.lf
anything is damaged,please contactwith Us to replace a new one.
Installation in strucstions:
1. The full set of cartridge seal is cleaned and exactly passed
leakage examine before sale.Inorder to avoid damage,don't
disassemble and clean the parts again before fixing.
2 The fitting allowance between the seal and shaft is dl h6 0.8,and there should be leading-inedge at the end of shaft.The outside diameter of shaft at the position of screw should be 01 0.2mm smaller,resisting the screw over-tighten.Lubricate the shaft with oil
3. Place the cartridge seal into the pump chamber,then:
A: Tighter four screw bolts of flanges,ensuring the medium leading
in hole"G"at the top Position
B : Tighter four set screws and position the shaft sleeve on the
shaft.
C: Remove four gauge plates.Please keep them and they wil be used
in future installation and
disassemble.
D: Connect the medium lead_in pipe with hole"G"in order to flush
away the friction heat and
flushing the seal chamber when pump running.
Note:
ter complete the installation,turning the shaft by hand to check
for the rotationi he shat could not rotate smoothily,seal had been
improperly installed.
We would like lo sincerely ooperale with Clients to supply high qually products and senice We beleve in establishing a long:erm cooperalive relalionshipis lhe key to suceess
