Multi Stage Wilo Pump Mechanical Seal For Water Pump wilo-16mm unbalanced

EBARA 25mm mechanical seal for EVMS, EVMSG series pumps
Material:SIC/SIC/VITON/304
Shaft size :12mm 16mm 25mmMechanical seals for other Ebara series pumps are available:

Pump Model :
JES - JE, JESX - JEX/AGA - AGC/CD, CDX, 2CDX/DWO, DWC/CM(A-B-C-D) - CMR, CDA
PRA - PRN/SWS - SWT/COMPACT/MATRIX/CVM/MULTIGO/HVM/EVMG, EVM, EVML/
3M SERIES, 3S SERIES, 3P SERIES, 3PF SERIES/3LM SERIES, 3LS SERIES, 3LP SERIES, 3LPF SERIES
3D SERIES, 3DS SERIES, 3DP SERIES/MD, SB3, WINNER 4N, 4BHS, IDROGO
SF6, 6BHE(L), 8BHE(L)/OPTIMA, BEST ONE - BEST ONE VOX/BEST 2-5, RIGHT/DW - DW VOX
DS-DSF, DVS, DML-DMLV, DMLF-DMLVF, DL (W/C), DRD, EBAMIX, DRS/DUMPER (L)
D TANK, BEST BOX, SANIRELEV 11&22/Ego, Ego T, Ego ER, Ego B/MR B/MR S/LPS/ELINE, ELINED, LPC, LPCD

Q1: Can I get some samples?

A: Yes, sample order is available for quality check and market test. But you have to pay the sample cost and express cost.

Q2: Do you receive customized order?

A: Yes, ODM & OEM are welcomed.

Q3: What's the lead time.

A: According to the order quantity, small order usually need 3-5 days, big order need negotiation.

Q4: What's your warranty terms?

A: We supply 12 months warranty time.

Q5: What's your payment terms?

A: We receive T/T, Paypal, Cash and etc.

Q6:Can you make custom products

A: of course, we can customize your request. Our factory located in guangzhou, welcome to have a visit

Preperation:
1. Shaft Outside Diameter is within tolerance +-0.05mm
2. Shaft run out <0.1mm
3. Shaf end float <0.13mm
4, No sharp edges on the shaft over the o ring

Note:
During the installation,don't scratch or damage the o ring.lf anything is damaged,please contactwith Us to replace a new one.

Installation in strucstions:
1. The full set of cartridge seal is cleaned and exactly passed leakage examine before sale.Inorder to avoid damage,don't disassemble and clean the parts again before fixing.

2 The fitting allowance between the seal and shaft is dl h6 0.8,and there should be leading-inedge at the end of shaft.The outside diameter of shaft at the position of screw should be 01 0.2mm smaller,resisting the screw over-tighten.Lubricate the shaft with oil

3. Place the cartridge seal into the pump chamber,then:
A: Tighter four screw bolts of flanges,ensuring the medium leading in hole"G"at the top Position

B : Tighter four set screws and position the shaft sleeve on the shaft.
C: Remove four gauge plates.Please keep them and they wil be used in future installation and
disassemble.
D: Connect the medium lead_in pipe with hole"G"in order to flush away the friction heat and
flushing the seal chamber when pump running.

Note:
ter complete the installation,turning the shaft by hand to check for the rotationi he shat could not rotate smoothily,seal had been improperly installed.

We would like lo sincerely ooperale with Clients to supply high qually products and senice We beleve in establishing a long:erm cooperalive relalionshipis lhe key to suceess