Multifunctional Magnetic 180lm LED Handheld Spotlight For Hunting

Multifunctional Magnetic 180lm LED Handheld Spotlight For Hunting

Multifunctional Work Light / Magnetic LED Explosion-Proof Flashlight Outdoor Emergency Light

Scope of application

It is applicable to the IIC T1-T6 Group 1, Zone 2, Zone 1, underwater, and other work sites in various flammable and explosive places such as oil fields, metallurgy, railways, electricity, public security, and petrochemical enterprises to provide mobile lighting.

Product Structural Characteristics:

1. The imported light source is made of imported special high-brightness LED light source, which has low energy consumption, high luminous efficiency, soft light, no glare, does not cause visual fatigue of the operator's eyes, and improves work efficiency.
2. High-energy memory-free polymer lithium battery, high energy density, large capacity, no pollution, economic and environmental protection, recyclable, good high and low temperature performance, strong charge protection ability, long life, safety, reliability, health and safety, can be charged at any time After a full charge, the storage capacity for half a year should be no less than 95% of full capacity, and no less than 80% of full capacity within two years.
3. The intelligent L ED drive circuit makes the product safer and more reliable. The built-in battery protection board is equipped with over-charge, over-discharge, over-current and short-circuit protection devices to ensure the safety of battery use. Intelligent charger uses imported special management chip for charging, fast charging, high efficiency, prolong battery life, and is provided with overcharge and short circuit protection
4. Unique design, reasonable structure, novel and beautiful, long lighting time, can continuously illuminate for more than 15-25 hours without attenuation, the lamp head can be arbitrarily adjusted in the range of 135 ° and 180 °, the focal length can be adjusted, and there is no dead angle for lighting . The lamp can be magnetically adsorbed and is simple and convenient to use; the good waterproof structure design can work normally in the rain, and has strong penetrating power to water mist, suitable for rainy and foggy days and emergency situations.

Performance characteristics:
 Reliability: The entire product shell is made of high-strength bulletproof plastic, and the rear shell is made of non-breakable engineering plastic, which is resistant to strong impact, waterproof, and corrosion resistance.
 Safety: It adopts integrated isolation and explosion-proof design, compact structure, dustproof and waterproof; with battery protection function, it can effectively prevent the battery from overcharging and overdischarging.
 Energy saving: High-efficiency semiconductor light-emitting technology, compared with traditional light sources, can save up to 70℅ at the same brightness.
 Economical: Long-life LED, maintenance-free, no need to replace the bulb, no follow-up use cost.
 Environmental protection: high-performance lithium battery, green, environmentally friendly, no pollution, no memory, low self-discharge rate.
 Convenience: small size, light weight, convenient and comfortable to wear, reducing user load.
 Uniqueness: The lamp holder can adjust the angle arbitrarily within 0-130 degrees; it has a stroboscopic function to realize long-distance signal transmission; magnetic adsorption and waterproof design, can float on the water; choose strong light and working light according to work needs.

Instructions:
 Turn on and off the light: Press the light button once, the working light work mode; press the light button again, the strong light work mode; press the light button again, the main light turns off.
 Strobe control: long press the light button for three seconds, working in signal mode.
 Initial use: Please make sure that the battery is sufficient for more than six hours before use. Long-term storage is affected by the self-discharge of the battery, and the control circuit protects the battery so that the battery has no voltage. Therefore, it is a normal phenomenon that the lamp cannot work before charging.

Structure function:
①Light source: light emitting diode
②Light button: switch light
③Charging jack: 4.5V@ 1A

caveat:
 Charging or disassembling the flashlight must be done in a safe place.
 Recharge in time after each use.

Precautions:
When charging or continuously discharging in a place with high ambient temperature, the surface of the torch will heat up slightly, which is a normal phenomenon.