Active Member
|
[China]
Address: No.1 Yanfa 1st Road, Songshan Lake High-tech Industrial Development Zone, Dongguan City 523000, Guangdong Province, China.
Contact name:Wu
ATMARS INDUSTRTY CO., LIMITED |
|
|
Reach in Laboratory High and Low Temperature Test Chambers Manufacturer
What is a TEMPERATURE TEST CHAMBER ?
ATMARS AT series reach-in / compact environmental test chambers can create a wide range of temperature and relative humidity levels (Optional) with the maximum being -80℃ to 200℃ (standard models: -70℃ to 150℃) and 1% to 98% RH (standard models: 20% to 98% RH). Whether you need to perform temperature cycling tests or expose your specimen to a steady state temperature environments, our chambers will maintain precise and accurate temperature/humidity control throughout your test.
And you can select from a variety of sizes, ranges, and options to meet your specific environmental testing requirements. Users will enjoy high quality & reliability, the ease of use, low maintenance requirements of our temperature humidity chambers and allow you to maximize product testing efficiency without sacrificing quality.
In additional to being much more functional, ATMARS test chambers
have a sleek, beautiful, contemporary appearance.
ATMARS reach-in standard models workspace volumes include: 80L, 100L, 150L, 225L, 408L, 800L, 1000L to walk-in /drive-in
sizes. And interior dimensions can be customized according to specimen
sizes and your testing requirements.
AT/AH Configurations:
AT Series - Temperature only
AH Series - Temperature and humidity capability
And also
ATB - Benchtop Models
ATW - Walk in Models (modular or welded)
ATD - Drive in Models
ATE - Explosion-proof Models
Available in FOUR standard temperature ranges:
Type A: -20℃ to 150℃
Type B: -40℃ to 150℃
Type C: -60℃ to 150℃
Type D: -70℃ to 150℃
with the maximum being -80℃ to 200℃ (standard models: -70℃ to 150℃)
and (Optional Humidity) 1% to 98% RH (standard models: 20% to 98%
RH)
| Technical Specifications of AT-100 SERIES Temperature Test Chambers Performance is based on ambient temperature +20 ℃ or circulating water temperature +25 ℃, empty load no specimen. | |||||
| Model | AT-100A | AT-100B | AT-100C | AT-100D | |
| T&H Adjustment Mode | Smart balanced temperature (humidity) control - BT(H)C | ||||
| Performance | Temperature Range | -20℃ to +150℃ | -40℃ to +150℃ | -60℃ to +150℃ | -70℃ to +150℃ |
| Temperature Fluctuation | ±0.5℃ | ||||
| Temperature Uniformity | ±2.0℃ | ||||
| Temperature Devitaion | ±2.0℃ | ||||
| Heat-up Rate (Average) | From -20℃ to +150℃ 3℃/min. | From -40℃ to +150℃ 3℃/min. | From -60℃ to +150℃ 3℃/min. | From -70℃ to +150℃ 3℃/min. | |
| Cool-down Rate (Average) | From +20℃ to -20℃ 1℃/min. | From +20℃ to -40℃ 1℃/min. | From +20℃ to -60℃ 1℃/min. | From +20℃ to -70℃ 1℃/min. | |
| Workspace Volume | 100L | ||||
| Workspace Dimensions | W500xD400xH500mm | ||||
| Exterior Dimensions | W750xD1400xH1500mm | ||||
| Material | Interior | #SUS304 Stainless Steel | |||
| Seal | Imported silicone seal | ||||
| Insulation | Expanded foam & fiberglass | ||||
| Exterior | Cold-rolled steel with powder coated surface | ||||
| System | Heating | Nichrome Resistance Wire Heater | |||
| Refrigeration | Mechannical Refrigeration System | ||||
| Controller | Programmable Touch-screen Controller | ||||
| Noise Level | ≤70dB (A-weighted sound pressure level measured at a distance of 1.0 meter) | ||||
| Allowable Ambient Conditions | Temperature: +5℃ to +35℃; Relative humidity: ≤85％RH (No condensation); Air pressure: 86kPa to 106kPa. | ||||
| Power Supply | AC 380 (1±10％)V (50±0.5)Hz 3 Phase 4 Wire plus Earth Wire | ||||
| ▲Custom options are available. | |||||
Test Standards Conformance
GB/T 10586-2006 Specifications for damp heat chambers
GB/T 10592-2008 Specification for low/high temperature test
chambers
GB/T 2423.1-2008 Environmental testing - Part 2: Test methods -
Tests A: Cold
GB/T 2423.2-2008 Environmental testing - Part 2: Test methods -
Tests B: Dry heat
GB/T 2423.3-2016 Environmental testing—Part 2: Testing method—Test
Cab: Damp heat,steady state
GB/T 2423.4-2008 Environmental testing for electric and electronic
products - Part 2: Test method - Test Db: Damp heat, cyclic
(12h+12h cycle)
GB/T 2423.22-2012 Environmental testing - Part 2: Tests methods -
Test N: Change of temperature
GJB 150.3A-2009 Laboratory environmental test methods for military
material - Part3: High temperature test
GJB 150.4A-2009 Laboratory environmental test methods for military
material - Part4: Low temperature test
GJB 150.9A-2009 Laboratory environmental test methods for military
material - Part9: Damp heat test
IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test
A: Cold
IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test
B: Dry heat
IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test
N: Change of temperature
IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test
Db: Damp heat, cyclic (12 h + 12 h cycle)
IEC 60068-2-78:2012 Environmental testing - Part 2-78: Tests - Test
Cab: Damp heat, steady state
