Home Companies Shenzhen Wisdomlong Technology CO.,LTD

Industrial Servo Motor Yaskawa 5.39N.m 200V AC Servo Motor SGMGH-09ACA61

Contact Us

[China]

Trade Verify

Address: 23E BlockB,Lushan Building，Chunfeng Road,Luohu District,Shenzhen,518001,China

Contact name:Eva

Shenzhen Wisdomlong Technology CO.,LTD

Verified Suppliers

Trust
Seal
Verified
Supplier
Credit
Check
Capability
Assessment

Industrial Servo Motor Yaskawa 5.39N.m 200V AC Servo Motor SGMGH-09ACA61

Country/Region	china
City & Province	shenzhen guangdong
Categories	Chargers

Product Details

Industrial Servo Motor Yaskawa 5.39N.m 200V AC Servo Motor SGMGH-09ACA61

QUICK DETAILS

Power : 850W
Voltage:200V
Rated Current : 7.1A

DESCRIPTION

AC Servo Motor
SGMAV Sigma-5
YASKAWA ELECTRIC

SEPCIFICATIONS

Brand Name	Yaskawa
Model Number	Industrial Servo Motor Yaskawa 5.39N.m 200V AC Servo Motor SGMGH-09ACA61
Place of Origin	Japan
Current	7.1A
Voltage	200V
Speed	1500/min
Power	850W
Ins	F
N.m	5.39

* Are external motor disconnects required between the motor and the VFD? Service disconnects at motor loads are very often used for maintenance purposes. Normally, removing a load from a VFD while operating does not pose a problem for the VFD. On the other hand, introducing a load to a VFD by closing a motor disconnect while the VFD is operational can be fatal to the VFD.

When a motor is Started at full voltage, as would happen in this case, high currents are generated, usually about six times the full load amps of the motor current. The VFD would see these high currents as being well beyond its capabilities and would go into a protective trip or fail altogether. A simple solution for this condition is to interlock the VFD run permissive circuit with the service disconnects via an auxiliary contact at the service disconnect. When the disconnect is closed, a permissive run signal restarts the VFD at low voltage and frequency.

* Are there power factor correction capacitors being switched or existing on the intended motor loads? Switching of power factor capacitors usually generates power disturbances in the distribution system. Many VFDs can and will be affected by this. Isolation transformers or line reactors may be required for these applications.

Power factor correction at VFD-powered motor loads is not necessary as the VFD itself does this by using DC internally and then inverting it into an AC output to the motor. All VFD manufacturers warn against installing capacitors at the VFD output.

Variable Frequency Drive Technologies
Three basic types of variable frequency drives offer certain advantages as well as disadvantages
depending on your motor application. The new flux vector drive is also discussed.

While all variable frequency drives (VFDs) control the speed of an AC induction motor by varying the motor's supplied voltage and frequency of power, they all do not use the same designs in doing so. There are three major VFD designs commonly used today: pulse width modulation (PWM), current source inverter

Installing the Servomotor

Servomotor SGM and SGMP types can be installed either horizontally or vertically. However, if the Servomotor is installed incorrectly or in an inappropriate location, the service life will be shortened or unexpected problems will occur. To prevent this, always observe the installation instructions described below.

Before installation:

Anticorrosive paint is coated on the edge of the motor shaft. Clean off the anticorrosive paint thoroughly using a cloth moistened with thinner.

NOTE

Avoid getting thinner on other parts of the Servomotor when cleaning the shaft.

Storage:

When the Servomotor is to be stored with the power cable disconnected, store it in the following temperature range:

Between −20°C and 60°C

Installation sites:

The Servomotor SGM and SGMP types are designed for indoor use.

Install Servomotor in an environment which meets the following conditions:

Free from corrosive and explosive gases
Well-ventilated and free from dust and moisture
Ambient temperature of 0 to 40°C
Relative humidity of 20% to 80% (non-condensing)
Inspection and cleaning can be performed easily

If the Servomotor is used in a location subject to water or oil mist, install a shield cover over the Servomotor.

SIMILAR PRODUCTS

SGMAV-04A3A6C	SGMAV-04ADA21
SGMAV-04ADA2C	SGMAV-04ADA61
SGMAV-04ADAH12C	SGMAV-04ADAHB21
SGMAV-06A3A21	SGMAV-06A3A61
SGMAV-06A3A6C	SGMAV-06A3A6S
SGMAV-06ADA21	SGMAV-06ADA2C
SGMAV-02A3A6S	SGMAV-02ADA21
SGMAV-08A3A61	SGMAV-02ADAHB21
SGMAV-08ADA21	SGMAV-08A3A2C
SGMAV-08A3A21	SGMAV-06ADAHB21

OTHER SUPERIOR PRODUCTS

Yasakawa Motor, Driver SG-	Mitsubishi Motor HC-,HA-
Westinghouse Modules 1C-,5X-	Emerson VE-,KJ-
Honeywell TC-,TK-	GE Modules IC -
Fanuc motor A0-	Yokogawa transmitter EJA-

Contact person: Anna Bao

Cellphone: +0086-13534205279

E-mail: wisdomlongkeji@163.com