Active Member
|
[China]
Address: No.116.Chengyang Road, Xiangcheng district , Suzhou , China.
Contact name:LV
oepoch industrial technology |
|
|
V90N SERIES
Swash-plate Type Axial Piston Double Pump
Features
Technical data
| Size | V90N130 | V90N165 | |
| Displacement(cc/rev) | 130×2 | 165×2 | |
| Speed | Rated speed (rpm)*1 | 2200 | 2100 |
| Maximum speed (rpm)*2 | 2500 | 2400 | |
| Minimum speed (rpm) | 600 | 600 | |
| Pressure | Rated pressure (bar) | 380 | 380 |
| Maximum pressure (bar) | 420 | 420 | |
| Maximum torque (N.m) @Vgmax and Δp=380bar | 2×786 | 2×998 | |
| Case volume (L) | 2.8 | 3.4 | |
| Suction port pressure (abs bar) | 0.7～2 | ||
| Drain pressure (bar) | 1 | ||
| Max. drain pressure (bar) | 3 | ||
| Mass (Kg) | 166 | ||
| Temperature range (℃) | -20～95 | ||
| Hydraulic fluid viscosity range (mm2/s) | 10～1000*3 (optimum viscosity range 16～36) | ||
1 Steady state suction pressure should be 0MPa and above (at normal condition);
2 If suction pressure less than 0 bar, Boost pressure should be required;
3 In case of 200-1000mm2/s, please allow system to warm up before using machine.
Type introduction
| V90N | 130 | A | V | R | ED2 | M | C | / | F3 | J1 | NN | K0 | G | M | |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 |
Product series
| 1 | Double pump, variable swashplate design,open circuit | V90N |
Displacement
| 2 | Displacement cc/rev | 130 | 165 |
Product series
| 3 | Design code | ● | A |
Seals
| 4 | FKM | ● | V |
Direction rotation
| 5 | Clockwise | ● | R |
| Counter-clockwise | o | L |
Control type
| 6 | Electric proportional displacement | Electro-proportional displacement control, positive displacement control, 12V | o | ED1 |
| Electro-proportional displacement control, positive displacement control, 24V | ● | ED2 | ||
Negative displacement control | Hydraulic pilot negative flow + Electro-proportional power control + (total power control) | o | HP1 |
Connector for solenoids
| 7 | Without(For hydraulic control) | o | N |
| Deutsch, DT04-2P | ● | M |
Swashplate angel indicator
| 8 | Without indicator | ● | N |
| With swashplate indicator, 5VDC | o | C |
Mounting flange
| 9 | 130 | 165 | Code | |
| SAE J617 N0.3 flywheel flange | ● | F3A | ||
| SAE J617 N0.3 flywheel flange | ● | F3B | ||
| SAE J617 N0.2 flywheel flange | ● | F4 |
Input shaft
| 10 | Input shaft size | 130 | 165 | Code |
| SAE J744-44-4 13T 8/16 | ● | ● | S5 | |
| JISD2001 40X14X2.5 | ● | ● | J1 | |
| JISD2001 47.5X17X2.5 | ● | ● | J2 |
Through drive
| 11 | None | ● | NN |
| SAE A 82-2 SAE J744-16-4 9T 16/32DP | o | A1 | |
| SAE A 82-2 SAE J744-19-4 11T 16/32DP | o | A2 | |
| SAE B 101-2 SAE J744-22-4 13T 16/32DP | o | B1 | |
| SAE B 101-2 SAE J744-25-4 15T 16/32DP | o | B2 |
Pilot control source
| 12 | External pilot supply, without pilot gear pump | o | NN |
| With pilot gear pump and pressure relief valve (only for none through drive) | o | K0 |
Connection type (except inlet and outlet port)
| 13 | UNC port, IS011926 | o | A |
| Metric port, ISO 6149 | o | M | |
| BSPPG thread, JISB2351 | ● | G |
Thread type of Flange Port
| 14 | UNC threads(only for UNC port) | o | A |
| Metric thread | ● | M |
Standard version/Special version
| 15 | Standard version | ● | Blank |
Note: Marked with " o " means under development.
ED1/ED2 Electro-proportional displacement control principle
Electro-proportional displacement control: With pilot-pressure-related control, the pump displacement is adjusted in proportion to the pilot pressure. Basic position without pilot signal is Vg min, which includes the mechanically depressurized basic position Vg min.
With increasing pilot pressure the pump swivels to a larger displacement.
The necessary control power is taken from the operating pressure or the external control pressure applied to port P. If the pump is to be adjusted from the zero basic setting or from a low operating pressure, port P must be supplied with an external control pressure of at least 30 bar, maximum 50 bar.
Note:
When ordering, please provide the information as below:
·Working pressure ·Maximum flow ·Minimum flow
Negative flow control schematic
Installation size
·V90N 130 type
·V90N 165 type
Port Details
| Port Name | Port Size and Description | |
| P1,P2 | Output Port | 1" SAE J518C Code 62 (6000psi) |
| 4XM12 depth 17mm | ||
| S1 | Input Port | 3-1/2" SAE J518C Code 61 (500psi) |
| 4XM16 depth 27mm | ||
| T1,T2 | Drain Port | G1 1/4 |
| G | External Control Pressure Port | G 1/4 |
| MA1, MA2 | Pressure Measureing | G 1/4 |
| Pi | Output Port | G 1/2 |
| Si | Input Port | G 3/4 |
·'F3' Type flywheel flange
F3A Type F3B Type
·'F4' Type flywheel flange
·Input shaft
| Size | D1 | L | L1 | L2 | |||
| F3A | F3B | F4 | |||||
| 130 | S5 | 44.45 | 58 | 75.7 | 48 | 33 | - |
| J1 | 39.5 | ||||||
| J2 | 47 | ||||||
| 165 | S5 | 44.45 | 64 | 82.8 | - | - | 60 |
| J1 | 39.5 | ||||||
| J2 | 47 | ||||||
