Results foriec61032 test sphere probefrom 3298 Products.
|
|
Quality Control Abrasion Testing Machine / Textile Fabric Martindale Abrasion Tester Model: RS-8306 Purpose: This testing machine is suitable for testing anti-abrasion performance ...
|
|
|
|
|
Test Probe 11 , IEC61032-figure 7 Test Finger Probe , Unjointed test finger According to IEC61032 figure 7 1,Knurled Finger Diameter:12mm 2,Knurled Finger Length:80mm 3,Dam- board ...
|
|
|
|
|
IEC 60529 Test Sphere50mm , IP1X This probe is intended to verify the protection of persons against access to hazardous parts. It is also used to verify the protection against ...
|
|
|
|
|
IEC 60529 Test Sphere 50mm, IP1X This probe is intended to verify the protection of persons against access to hazardous parts. It is also used to verify the protection against ...
|
|
|
|
|
EN 50636 Figure 1 Test Finger Probe Young Adult Arm Probe Stainless Steel Probe Standard description Our product of Test Finger Probe (see Figure 1)shall not to be able to make ...
|
|
|
|
|
UL 1278 Figure 10.1 Cone Test Finger Probe for Heating Elements Product details: This probe conforms to the standard requirement of UL1278 Fig 10.1. The handle is made of nylon ...
|
|
|
|
|
UL Test Probe Test Pin Jointed Test Finger Test Fingernail Test Tongue UL standards Articulated Test Probes for electrical safety accessibility test on Protection of persons and ...
|
|
|
|
|
EN 50636-2-100 Figure 2 Adult Arm Probe EN 13683-2003 Figure 5 Product information: The adult arm probe conforms to EN 50636-2-100 figure 2 and EN13683-2003: 5.2.1.3 fig 5. It is ...
|
|
|
|
|
Telecom Test Probe Usage: Check access to telecommunications voltages. The Telecom Access Probe is required in IEC 60950, IEC 60065, UL and CSA Standards. It is used to check ...
|
|
|
|
|
IT Test Probe Ø12mm, 80mm long with tip radius 6mm Conforms to IEC60950, GB4943
|
|
|
|
|
Wedge Probe For Document Shredder The wedge probe is one of two new accessibility probes required by UL 60950 for paper shredders. UL found that children and small women could ...
|
|
|
|
|
UL 60335-2-24-Figure 101.DVA.1 – Articulate probe with flat and cone shaped hand 3.5 – 4.5 year age Notes: 1 – The probes were designed with a center pin to rotate the hand with ...
|
|
|
|
|
UL Enamel Wire Probe 25 Usage: This probe is use to checking access to enamel coated wire accord to UL standard requirement. stainless steel with stainless stell handle.
|
|
|
|
|
UL Standard Articulated Jointed Test Finger For Preventing The Finger From Approaching To The Hazardous Parts Test Finger Length: 234mm The Bending Part Length: 30/30/40mm The UL ...
|
|
|
|
|
Test Rubber Ball Usage rubber ball used for dynamic stability testing to UL (USA) standards. A ball, 2 and 3/4/16 inch diameter (2.187 inches), filled with No. 60 core sand. It is ...
|
|
|
|
|
Antenna coaxial sockets mounted on the apparatus Antenna coaxial sockets mounted on the apparatus and incorporating parts or components which isolate HAZARDOUS LIVE parts from ...
|
|
|
|
|
IEC 60529 Test rod 2.5mm, IP3X Usage This wire is intended to verify the protection of persons against access to hazardous parts. It is also used to verify the protection against ...
|
|
|
|
|
Test Needle Diameter : Ø0.5mm or Ø1mm, Length : 20mm
|
|
|
|
|
Rigid Finger 1 Ø50mm, 20mm wide, 100mm long
|
|
|
|
|
Test Probe D, IEC60529 Test Wire 1.0mm, IP4X Introduction: 1,According to: IEC61032:1997,IEC60529,IEC62368-1 2,Test Probe D is a necessary appliance for domestic and similar ...
|
|
|
