Uonel Co.Limtied |
|
The TBE board is mainly used to achieve cross-connection at the electrical layer and ALS.
For detailed functions and features, refer to Table 1.
Function and Feature | Description | |||
---|---|---|---|---|
Basic function |
The reverse process is similar. | |||
Client-side service type | FE: Ethernet service at a rate of 125 Mbit/s. Supports FE optical signals and FE electrical signals. GE: Ethernet service at a rate of 1.25 Gbit/s. Supports GE optical signals and GE electrical signals. 10GE LAN: Ethernet service at a rate of 10.31 Gbit/s 10GE WAN: Ethernet service at a rate of 9.95 Gbit/s NOTE: The TBE board supports both FE/GE electrical signal and FE/GE optical signal. For FE/GE electrical signal transmission, it is recommended that the board be equipped with at most two GE electrical modules to facilitate fiber routing. | |||
Cross-connect capabilities | OptiX OSN 6800:
OptiX OSN 3800:
| |||
Alarms and performance events monitoring |
| |||
ALS function | Supports the ALS function on the client side. NOTE: ALS function is supported only when EPL services (port <->
VCTRUNK) are provisioned. | |||
QinQ | supported | |||
QoS (Quality of Service) | Supports CAR (Committed Access Rate) and CoS (Class of Service). | |||
ETH OAM | Supports IEEE802.1ag and IEEE802.3ah-compliant ETH OAM protocol. | |||
LAG (Link Aggregation Group) |
| |||
VLAN broadcast | Supports VLAN-based service group broadcast. | |||
CVLAN group port | Supports a group of CVLAN to be used as one VLAN. | |||
Layer 2 switching | Supports the MAC address learning and aging. Supports one VB. | |||
Flow control | Supports IEEE802.3X-compliant Ethernet flow control protocol and flow control termination. | |||
EPL (Ethernet Private Line) | Provides point-to-point EPL dedicated line. | |||
EVPL (Ethernet Virtual Private Line) | Provides point-to-multipoint EVPL dedicated line and supports VLAN-based switching. | |||
Port working mode | 10GE optical interface: 10GE LAN, 10GE WAN GE optical interface: 1000MFULL, auto-negotiation GE electric interface: auto-negotiation FE optical interface: 100MFULL FE electric interface: 10MHALF, 10MFULL, 100MHALF, 100MFULL, auto-negotiation | |||
Protection schemes | Supports VLAN SNCP. Supports DBPS protection. Supports LAG protection. Supports DLAG protection. Supports ERPS protection. Supports client 1+1 protection. NOTE: RX/TX ports do not support client 1+1 protection. Client 1+1 protection is supported only when EPL services (port <-> VCTRUNK) are configured on the board. | |||
Test frame | Supported | |||
PRBS test function | Not supported | |||
LPT function | Supported NOTE: The LPT function cannot be configured for EVPL services but only
for bidirectional EPL services (port <-> VCTRUNK). When the
LPT function is enabled, Source C-VLAN and Sink C-VLAN of an EPL service must be left empty. | |||
Electrical-layer ASON | Not supported | |||
Loopback | 10GE optical interface | MAC | Inloop | Supported |
Outloop | Supported | |||
PHY | Inloop | Supported | ||
Outloop | Supported | |||
GE optical interface | MAC | Inloop | Supported | |
Outloop | Not supported | |||
PHY | Inloop | Supported | ||
Outloop | Not supported | |||
GE electric interface | MAC | Inloop | Supported | |
Outloop | Not supported | |||
PHY | Inloop | Supported | ||
Outloop | Supported | |||
FE optical interface | MAC | Inloop | Supported | |
Outloop | Not supported | |||
PHY | Inloop | Supported | ||
Outloop | Not supported | |||
FE electric interface | MAC | Inloop | Supported | |
Outloop | Not supported | |||
PHY | Inloop | Supported | ||
Outloop | Supported | |||
Protocols or standards compliance | Protocols or standards for transparent transmission (non-performance monitoring) | IEEE 802.1q VLAN All L2 protocols including xSTP, LACP, EthOAM, DHCP, PPP, etc. MPLS protocols All L3 protocols including ARP, IGMP, OSPF, IGRP etc. | ||
Protocols or standards for service processing (performance monitoring) | IEEE 802.3x pause frame IEEE 802.3ad LACP IEEE 802.1p priority IEEE 802.1q VLAN IEEE 802.1ag OAM IEEE 802.3ah OAM IEEE IGMP STP, RSTP, MSTP R-APS |
Specifications include optical specifications, dimensions, weight, and power consumption.
Board | Client-Side Fixed Optical Module | Client-Side Pluggable Optical Module |
---|---|---|
TN11TBE | N/A | 100 BASE-FX-10 km-eSFP 100 BASE-FX-80 km-eSFP 2.125 Gbit/s Multirate-0.5 km-eSFP 1000 BASE-LX-10 km-eSFP 1000 BASE-LX-40 km-eSFP 1000 BASE-ZX-80 km-eSFP 1.25 Gbit/s Multirate (CWDM)-40 km-eSFP 2.67 Gbit/s Multirate (CWDM)-80 km-eSFP 10 Gbit/s Multirate-10 km-XFP 10 Gbit/s Multirate-40 km-XFP 10 Gbit/s Multirate-80 km-XFP 10 Gbit/s Single Rate-0.3 km-XFP |
Parameter | Unit | Value | |||
---|---|---|---|---|---|
Optical Module Type | 2.125 Gbit/s Multirate-0.5 km-eSFP | 1000 BASE-LX-10 km-eSFP | 1000 BASE-LX-40 km-eSFP | 1000 BASE-ZX-80 km-eSFP | |
Line code format | - | NRZ | NRZ | NRZ | NRZ |
Optical source type | - | MLM | SLM | SLM | SLM |
Target transmission distance | - | 0.5 km (0.3 mi.) | 10 km (6.2 mi.) | 40 km (24.9 mi.) | 80 km (49.7 mi.) |
Transmitter parameter specifications at point S | |||||
Operating wavelength range | nm | 770 to 860 | 1270 to 1355 | 1270 to 1355 | 1500 to 1580 |
Maximum mean launched power | dBm | -2.5 | -3 | 0 | 5 |
Minimum mean launched power | dBm | -9.5 | -9 | -5 | -2 |
Minimum extinction ratio | dB | 9 | 9 | 9 | 9 |
Eye pattern mask | - | IEEE802.3z-compliant | |||
Receiver parameter specifications at point R | |||||
Receiver type | - | PIN | PIN | PIN | PIN |
Operating wavelength range | nm | 770 to 860 | 1270 to 1355 | 1270 to 1355 | 1500 to 1580 |
Receiver sensitivity | dBm | -17 | -20 | -23 | -23 |
Minimum receiver overload | dBm | 0 | -3 | -3 | -3 |
When accessing 1000 BASE-T services, the specifications of the electrical interface comply with the IEEE Std 802.3.
Parameter | Unit | Value | |||
---|---|---|---|---|---|
Optical Module Type | 10 Gbit/s Multirate-10 km-XFP | 10 Gbit/s Multirate-40 km-XFP | 10 Gbit/s Multirate-80 km-XFP | 10 Gbit/s Single-Rate-0.3 km-XFP | |
Line code format | - | NRZ | NRZ | NRZ | NRZ |
Optical source type | - | SLM | SLM | SLM | MLM |
Target transmission distance | - | 10 km (6.2 mi.) | 40 km (24.9 mi.) | 80 km (49.7 mi.) | 0.3 km (0.2 mi.) |
Transmitter parameter specifications at point S | |||||
Operating wavelength range | nm | 1290 to 1330 | 1530 to 1565 | 1530 to 1565 | 840 to 860 |
Maximum mean launched power | dBm | -1 | 2 | 4 | -1.3 |
Minimum mean launched power | dBm | -6 | -4.7 | 0 | -7.3 |
Minimum extinction ratio | dB | 6 | 8.2 | 9 | 3 |
Minimum side mode suppression ratio | dB | 30 | 30 | 30 | 30 |
Eye pattern mask | - | G.691-compliant | |||
Receiver parameter specifications at point R | |||||
Receiver type | - | PIN | PIN | APD | PIN |
Operating wavelength range | nm | 1260 to 1565 | 1260 to 1605 | 1270 to 1600 | 840 to 860 |
Receiver sensitivity (multirate)a | dBm | -11 | -14 | -24 | -7.5 |
Receiver sensitivity (10GE LAN) | dBm | -14.4 | -15.8 | -24 | -7.5 |
Minimum receiver overload (10GE LAN) | dBm | 0.5 | -1 | -7 | -1 |
Minimum receiver overload (STM-64)a | dBm | -1 | -1 | -7 | -1 |
Maximum reflectance | dB | -27 | -27 | -27 | -12 |
a: The sensitivity and overload in the table complies with ITU-T G.691. The actual sensitivity of 10 Gbit/s Multirate-10 km-XFP modules is -14.4 dBm, and the actual overload is 0.5 dBm, which can be used as the reference during deployment commissioning. |
Board | Typical Power Consumption (W) | Maximum Power Consumptiona (W) |
---|---|---|
TN11TBE | 40.7 | 44.8 |
a: The maximum power consumption is the power consumed by the board when it works normally under the highest ambient temperature. |
Cargo will be delivered within 1 day after payment arrived. Tracking Number will be offered once delivery done.
Delivery Options | Estimated Delivery Time |
---|---|
![]() | 3-5 business days |
![]() | 3-5 business days |
![]() | 10-20 business days |
Notice:
Above mentioned information are just for your reference only,we will keep you posted for the tracking delivery schedule.There are two delivery options available for by air and by sea:
Deliver to port:
Uonel is responsible for transporting goods to port. All
subsequent customs and transportation fees are the
responsibility of the buyer. Uonel will recommend trustworthy
local freight forwarders to you.Uonel can facilitate the progress
under buyer's permission and at buyer's expense.
Deliver to door:
Uonel will quote all destination charge prior once we have
confirmed order.
Uonel is responsible for transporting goods to door after you
have made the payment.
100% Low Price Guarantee:
Uonel provides
high-quality products at low wholesale prices
100% Quality Assurance:
All items are
ORIGINAL NEW and GENUINE only.
Free Technical Support:
Our FREE Expert Consultancy Support is over the phone, by chat, by email or by login remotely.
100% Money Back Guarantee:
You can contact our customer service team to exchange or return any
product that you bought from us.
Flexible Secure Payment & Shipment:
Verified
authorization: Mcafee Secure, VeriSign Secured
Return Material Authorization (RMA) Process
Standard Hardware Warranty Policy:
Original new sealed product: 1 Year
The Support Contacts:
If your products failed, you must contact your sales representative to verify product failure. If the problem still can't correct by remote support methods i.e. email or phone support, the RMA procedure will issue.
Uonel is one of the biggest Network Hardware distributor in china, founded in 2008. We are a global provider of netwotking products with more than 5000 customers.
We provide original new Routers,Switches,Firewalls,Wireless APs & controllers,OLTs,GPON modems,optical transceivers.Our company have more than $5million products in stock.
Most of our technical engineers had work exprience in company,we can provide network design&planning,configration,troubleshooting,maintenance and training service in world wide.