|
[China]
Trade Verify
Address: zhenglu town, tianning district, changzhou city, JIangsu Province
Contact name:Lillian
Jiangsu Shengman Drying Equipment Engineering Co., Ltd |
|
Verified Suppliers
|
|
|
Dry Liquids To Powder Centrifugal Spray Drying Equipment With Good Service
The atomizer forms the liquid into small droplets before spraying them into a hot air stream, where the major part of the water evaporates in a few seconds. At the end, the dried powder will be separated from the air by a cyclone and/or a filter system. Downstream the dryer can be equipped with fluid beds, coolers and agglomerators, to further condition the powder prior to the packaging unit.
Atomization can be provided by centrifugal wheels, rotary atomizers, pressure nozzles or twin-fluid nozzles. This range of systems allows the specific particle size requirements to be met for each application.
Direct or indirect heating systems are supplied depending upon the industry standards for the product. Inlet temperatures may range from 100°C for very heat sensitive products to 750°C for some inert chemicals.
Closed circuit and self-inertized dryers are supplied to allow organic solvents to be dried and to meet the environmental specifications.
Different chamber configurations are used along with a range of residence times to provide the desired particle size and moisture content in the finished powder.
Principle
After been filtered and heated the air enters into the air
distrbutor on the top of the dryer.The hot air enters into the
drying room in the spiral form and uniformly. Passing through the
high-speed centrifugal sprayer on the top of the tower,the material
liquid will rotate and be sprayed into the extremely fine mist
liquid beads.Trough the very short time of contacting the heat
air,the materials can be dried into the final products.The final
products will be discharged continuously from the bottom of the
drying tower and from the cyclones. The waste gas will be
discharged from blower.
Features
(1) Fast drying speed, material liquid after atomization, significantly increased surface area, in the hot air flow, instantaneous evaporation can be 95% 98% moisture, to complete the drying time only a few seconds, and especially suitable for drying of thermal sensitive material.
(2) Products with good uniformity, fluidity and solubility, the
product high purity, good quality.
(3) Production process is simple, convenient operation and control.
Special material for 40-60% moisture content (90%) of the liquid to
a dry powder products, dried without crushing and screening, reduce
the production process, improve product purity. To the product
particle size, bulk density, moisture, within a certain range can
be adjusted by changing the operating conditions, control and
management is very convenient.
Centrifugal spray atomizer Features
1.The drying speed is high when the material liquid is atomized,the
surface area of the material will increase greatly.In the hot-air
flow,95%-98% of water can be evaporated at a moment.The time of
completing the drying is only several seconds. This is especially
suitable for drying the heat sensitive materials.
2. Its final products own the good uniformity, flow ability &
solubility. And the final products are high in purity and good in
quality.
3. The production procedures are simple and the operation and
control are easy.The liquid with moisture contents of 40-60%(for
special materials,the contents might be up to 90%).can be dried
into the powder or particle products once a time. After the drying
process, there is no need for smashing and sorting,so as to reduce
the operation procedures in the production and to enhance the
product purity.The product particle diameters,looseness and water
contents can be adjusted through changing the operation condition
within a certain range. It is very convenient to carry out control
and managment.
Technical parameters
| Model | PLG | |||||
| 5 | 25 | 50 | 100 | 150 | 200-2000 | |
| inlet temperatyre ℃ | 140-350 automatically controlled | |||||
| outlet temperatyre ℃ | 80-90 | |||||
| Max water evaporation capacity kg/h | 5 | 25 | 50 | 100 | 150 | 200-2000 |
| centrifugal spraying nozzle transmission mode | compressed air transmission | mechaical transmission | ||||
| rotation speed (r.p.m) | 25000 | 18000 | 18000 | 18000 | 15000 | 8000-15000 |
| spraying desc diameter (mm) | 50 | 100 | 120 | 140 | 150 | 180-340 |
| max electric heating power (kw) | 9 | 36 | 63 | 81 | 99 | settled by customer |
| overall dimensions | 1.8*0.93*2.2 | 3*2.7*4.26 | 3.7*3.2*5.1 | 4.6*4.2*6 | 5.5*4.5*7 | depends on tryer |
| dried powder collection | ≥95 | ≥95 | ≥95 | ≥95 | ≥95 | ≥95 |
FAQ
1. Can I use this spray drying machine to extract some raw
materials?
Yes, in order to help you better, we suggest you provide the name
of the raw material you want to process.
2. Can I use my own raw materials for extraction test?
Yes, of course. We can do extraction tests and send videos and test
reports for your reference.
3. Do you have OEM service? Do you provide parts?
Yes, we will, as long as you provide us with your drawings and
detailed requirements.
4. How can we visit your factory?
If you arrive in Shanghai, you can tell us your specific location.
We will arrange a driver to pick you up.
5. How to transport equipmen?
We usually choose sea transportation. Laboratory models can be
shipped by air according to customer requirements.
6. What is the voltage of the equipment?
The equipment voltage is 380V, if the user requires 220V, the
specific can be customized according to the voltage standard of the
country where your equipment is used.
7. what is your after-sales service?
We provide the English manual of the equipment manual. If you need,
we will send an engineer to install and train workers.
