Active Member
|
[China]
Address: 3rd Floor,Zhixinmao Technology Park,Chuangxin Road,Tangxiachong,Bao'an District,Shenzhen,China
Contact name:Zhang
Shenzhen Zenhon Technology CO.,LTD |
|
|
HDMI 1.3 , Over Single CAT5e/6 , Full HD 1080P , Extender
INTRODUCTION
The HDMI to RJ45 Extender use single cat-5e or cat-6(recommended) cables up to 60 meters instead of HDMI cable to transmit high definition signal, for cutting down cost. Long distance transmission of high definition is very difficult because HDMI cable is very expensive and infrequent. The Extender is designed to supply for long distance transmission of high definition signal.
SPECIFICATION
| Length of CAT-6 cable between Transmitter and Receiver | Up to 60 meters |
| HDMI Input | 24/50/60fs/1080p/1080i/720p/576p/576i/480p/480i |
| Support audio format input | DTS-HD/Dolby-trueHD/LPCM7.1/DTS/Dolby-AC3/DSD |
| HDMI Output | 24/50/60fs/1080p/1080i/720p/576p/576i/480p/480i |
| Support audio format output | LPCM7.1/DTS/Dolby-AC3/DSD |
| Max bandwidth | 165MHz |
| Max baud rate | 4.95Gbps |
| Input Video signal | 0.5~1.5Volts p-p |
| Output DDC signal | 5Volts p-p (TT1L) |
| Input/Output HDMI cable distance | ≤20m AWG26 HDMI standard cable |
| Max working current | 800mA |
| Power adapter format | Input:AC (50HZ, 60HZ) 100V*240V; Output: DC5V/1A |
| Operating Temperature range | (-15 to +55℃) |
| Operating Humidity range | 5 to 90%RH (No Condensation) |
FEATURES
1. Signal transmission :CAT5e or CAT6(recommended) cables up to 60 meters instead of HDMI cables are connected between TX and RX Extender.
2. Support HDMI1.3,HDCP 1.2 protocol compliant.
3. Support video input : 24/50/60fs/1080p/1080i/720p/576p/576i/480p/480i.
4. Support video output : 24/50/60fs/1080p/1080i/720p/576p/576i/480p/480i.
5. Support CEC.
6. Support 20~60KHz dual IR working.
PANEL DESCRIPTIONS
Please study the panel drawings below and become familiar with the signal
input(S),output(S)and power requirements.
DC/5V-------------------------------------------Power Input
Power---------------------------------------Power Indicator
HDMI Input -------------------------------HDMI Input port
IR-TX -----------------------------------------IR transmitter
IR-RX --------------------------------------------IR receiver
CAT5e/6 Out -----------------------------CAT5e/6 output
EDID -------------------------------------EDID copy button
IR-TX -----------------------------------------IR transmitter
IR-RX --------------------------------------------IR receiver
CAT5e/6 In --------------------------------CAT5e/6 Input
DC/5V------------------------------------------Power Input
Power -------------------------------------Power Indicator
HDMI Output --------------------------HDMI output port
CONNECT AND OPERATE
Before installation, please make sure all devices you wish to connect have been turned off.
1. Connect HDMI signal source to the transmitter of HDMI extender.
2. Use LAN cable(Recommend:CAT5e/6) to connect transmitter and
receiver of HDMI Extender.
3. Connect the display equipment with HDMI connector to the receiver of
HDMI extender.
4. Power on all connected devices, Choose the input of the display device
to its HDMI channel.
