Home Companies GUANG ZHOU CITY FREESEA ELECTRICAL CO., LTD

1hp 2hp 3hp 4hp 5hp Spa Water Pump With Anodized Motor Body Long Lifespan

Active Member

Contact Us

[China]

Address: 6th Floor,NO. 8, Aobang Plaza, Rd 2nd, Wanggang Gongye Street， Baiyun District, Guangzhou

Contact name:Sindy Jin

GUANG ZHOU CITY FREESEA ELECTRICAL CO., LTD

1hp 2hp 3hp 4hp 5hp Spa Water Pump With Anodized Motor Body Long Lifespan

Country/Region	china
City & Province	guangzhou guangdong
Categories	Pumps

Product Details

1hp 2hp 3hp 4hp 5hp Head Clean Pool Pump Impeller Swimming Pool Pump 1.1hp

Model	Voltage	HZ	Power(KW)	Power(HP)	Hmax(m)	Qmax(m³/h)	Port Size(inch/mm)
FL-150	220V-240V	50/60	1.1	1.5	18	30	2.0/63
FL-200	220V-240V	50/60	1.5	2	19	35	2.0/63
FL-300	220V-240V	50/60	2.2	3	20	38	2.0/63
FL-350	220V-240V	50/60	2.6	3.5	21	40	2.0/63
FL-400	380V	50/60	3	4	22	48	2.0/63

Features:

1. Excellent Flow rate suitable for spas and pools up to 2000 litres

2. Suitable for spas including Salt, Chorine, Inground and Above Ground

3. Corrosion Resistant and Chemical-resistant thermoplastic body

4. Tough durable construction for longer lasting life

5. Built-In Thermal Protection

6. Instruction manual for ease of installation and use.

7. Anti spin-off impeller.

8. A large see-through strainer, super-size debris basket.

9. Special design shockproof basement

10. Good quality and modern design

11. Low operation noise

12. Single or three phase

13. Anodized motor body

14. Huge pro-filter for less cleaning maintenance

Release all air from fitter and piping system: see filter owner manual

In a flooded suction system (water source higher than pump),
pump will prime.
it self when suction and discharge valves are opened.
If pump is not in a flooded suction system, unscrew and remove cap
cover; fill cap and pump with water.
Clean and inspect Ring; re-install on trap cover.
Replace cap cover on cap turn clockwise to tighten cover.
PRIMING PUMP
NOTICE:
Tighten cap cover by hand only
Pump should prime now. Priming time will depend on vertical length of suction lift and horizontal
of suction piping.
ROUTINE MAINTENANCE
The only routine maintenance is inspection/cleaning basket. Debris or trash that collects in basket,
well choke off water flow through the pump. Follow instructions below to clean basket:
Stop pump, close gate valve in suction and discharge, and release all pressure from
system before proceeding.
1. Unscrew cap lid(turn counterclockwise).
2. Remove strainer basket and clean. Be sure all holes in basket are clear, flush basket with water.
If basket is replaced backwards, cover will not fit on pre-filter body.
3. Clean and inspect lid Ring: re-install on cap cover.
4. Clean Ring groove on pre-filter body and Replace lid. To help keep lid from sticking, tighten
hand tight only.
5. Prime pump (see priming instructions above)

Description:

HOW TO USE – It is best to always replace your pump with a pump of similar size and power rating. Changing over and fitting of the pump can be done by the handy person but it is recommended to get it done by a professional. Suitable as a direct replacement OR upgrade to existing pump.

This pump is ideal for pool pumping, cleaning, hot water circulation etc. Sometimes people use it for increasing the water pressure in the pipe, garden sprinkling, and irrigation. It only needs solar off grid power to get work! Delivery head of 14 meters and suction up to 8 meters. This pump is simple to install and easy to use. No need of sophisticated knowledge of pumping but just a little imagination of how much you can do with it. It will pump up the water in no time.