Results forgx53 lamp cap gaugefrom 4669 Products.
|
Test Gauges for Lamp Caps and Holders HDJ0001 Standard: IEC 60598-1: Luminaires - Part 1:General requirements and tests; IEC 60061-3: Lamp caps and holders together with gauges for ...
|
|
|
|
B22 Go No Go Gauge of Finished Lamp Caps Include: 1) IEC60061-3 7006-11-8 B22 Go Gauges for Caps on Finished Lamps; Purpose: To check dimensions A max., N min. D1 min., D1 max., ...
|
|
|
|
B15 Go No Go Gauge of Finished Lamp Caps Include: 1) IEC60061-3 7006-11-8 B15 Go Gauges for Caps on Finished Lamps; Purpose: To check dimensions A max., N min. D1 min., D1 max., ...
|
|
|
|
Not go gauge for caps on finished lamps E17, 7006-28F-1 Purpose: To check the minimum outside (major) diameter of the screw thread, dimension d, of E12 caps on finished lamps. ...
|
|
|
|
Go gauge for caps on finished lamps E12, 7006-27H-1 Purpose: To check the maximum dimensions of the screw thread and dimension T1 minimum of E12 caps on finished lamps. Testing: ...
|
|
|
|
Go gauge for caps on finished lamps E17, 7006-27K-1 Purpose: To check the maximum dimensions of the screw thread and dimension T1 minimum of E17 caps on finished lamps. Testing: ...
|
|
|
|
Go gauge for E14 caps on finished lamps, 7006-27F-1 Purpose: To check the maximum dimensions of the screw thread and dimension T1 minimum of E14 caps on finished lamps. Testing: ...
|
|
|
|
Not go gauges for caps on finished lamps B22, 7006-10-8 According to standard IEC 60061-3 Purpose: To check dimension A in, of caps B22 on finished lamps. Testing: Caps on finished ...
|
|
|
|
Go gauge for caps on finished lamps E12, 7006-27H-1 Purpose: To check the maximum dimensions of the screw thread and dimension T1 minimum of E12 caps on finished lamps. Testing: ...
|
|
|
|
The sharp part of the edge of the thread shall be broken with a radius of 0.2 mm to 0.3 mm. PURPOSE: To check the maximun dimensions of the crew thread and dimension T1 min, of E39 ...
|
|
|
|
Go gauge for caps on finished lamps E40, 7006-27-7 Purpose: To check the maximum dimensions of the screw thread and dimension T1 minimum of E40 caps on finished lamps. Testing: ...
|
|
|
|
Go gauges for caps E26, E26/50x39, E26/51x39 & E26d, 7006-27D-3; Purpose: To check the maximum dimensions of the screw thread and dimension T1 minimum of E26, E26/50x39, E26/51x39 ...
|
|
|
|
Not go gauges for caps on finished lamps B22, 7006-10-8 According to standard IEC 60061-3 Purpose: To check dimension A in, of caps B22 on finished lamps. Testing: Caps on finished ...
|
|
|
|
Not go gauges for caps on finished lamps B15, 7006-10-8 According to standard IEC 60061-3 Purpose: To check dimension A in, of caps B15 on finished lamps. Testing: Caps on finished ...
|
|
|
|
The drawing is intended only to illustrate the essential dimensions of the gauge. For details of cap E39, see sheet 7004-24A. PURPOSE: To check the minimum outside (major) diameter ...
|
|
|
|
Go gauges for caps on finished lamps BA9, B15, BA15 & B22, 7006-11-8. According to standard IEC 60061-3 Purpose: To check dimensions A max., N min. D1 min., D1 max., and the ...
|
|
|
|
Purpose: To check the minimum outside (major) diameter of the screw thread, dimension "d" of E27 caps on finished lamps shown on sheet 7006-21. Testing: When the gauge is placed ...
|
|
|
|
Go and not go gauge for unmounted bi-pin cap(not for use on finished lamps) G13, 7006-44-4 Purpose: To check dimensions E min., E max., F min., G max., H max. and the combined pin ...
|
|
|
|
Go gauge for dimension "S1" of E27 caps on finished lamps, code 7006-27C-1 Purpose: To check the dimension S1 minimum and S1 maximum of E27 caps on finished lamps shown on sheet ...
|
|
|
|
Purpose: To check dimensions A max., N min. D1 min., D1 max., and the diametrical position of the pins of caps B15 on finished lamps. Testing: The cap shall enter the gauge until ...
|
|
|