Active Member
|
[China]
Address: No.907,Jiuzhou Building,High-Tech Park,Nanshan, Shenzhen, China
Contact name:Yonchin Shou
Cabsat industrial limited |
|
|
VDSL Modem VDSL IAD Integrated Access Device with 2.4G/5.0G Dual Wifi VDB1421-W2 (1GWan+4GE+2FXS)
Feature:
Platform Model: VDM306-1
Fully configuration:
1*DSL+1*GE(WAN)+4*FE(LAN) +1*USB2.0+2.4G 2*211n wifi
(Ports and Wifi mode optional according to customer requirements)
Router is a versatile, high-speed remote router for home and the
small office.
Specifications:
1. User Interface
| 2.1 Key Component | |
| Key Component | Description |
| Network Processor | EN7512 |
| VDSL AFE | MT7556 |
| WLAN Chipset | MT7592 11n2x2 |
| Memory | 128MB SPI NAND Flash 128MB DDR(Integrate) |
| Product Feature | Description |
| WAN | 1x inner pair RJ-11 DSL port |
WAN LAN | Standard Compliance with ITU-T Rec. G.993.2 |
| 4x 10/100Base-TX MDI/MDIX RJ-45 ports | |
LAN USB Interface | Compliant with following standards: |
| 1.IEEE 802.3/802.3u | |
| 2.Hardware based 10/100, full/half, flow control auto negotiation | |
| 3.Non-blocking wire speed reception and transmission | |
| 4.Full duplex IEEE 802.3x flow control and half duplex back-pressure flow control | |
| 5.Broadcast storm protection | |
| 6.Automatic address learning, address aging and address migration | |
| 7.Integrated address Look-Up Engine, 1 K absolute MAC addresses supported | |
| 1*USB2.0 Host ports, Type A connector | |
| WLAN | 2x internal MIMO antenna by default |
WLAN Power Switch | IEEE 802.11b, IEEE 802.11g, IEEE802.11n compliant |
| Operating Frequency: | |
| 2.4GHz Band: 2400 ~ 2497MHz ISM band | |
| Output Power: | |
| Ÿ The maximum allowable RF power level is subject to specified nation regulation. | |
| Ÿ Typical RF Output Power (tolerance +/-2dB) and Data Rate at each RF chain, and at room Temp. 25degree C | |
| 802.11n section for 2.4G Band: | |
| HT20 | |
| - 15dBm at MCS0, 1 | |
| - 15dBm at MCS2, 3 | |
| - 15dBm at MCS4, 5 | |
| - 13dBm at MCS6, 7 | |
| HT40 | |
| - 15dBm at MCS0, 1 | |
| - 15dBm at MCS2, 3 | |
| - 15dBm at MCS4, 5 | |
| 802.11g: | |
| - 15dBm at 6M/9M bps | |
| - 15dBm at 12M/18M bps | |
| - 15dBm at 24M/36M bps | |
| - 13dBm at 48M/54M bps | |
| 802.11b: | |
| Typical 15dBm (+/-2dB) at 11, 5.5, 2, and 1Mbps | |
| Peak Gain: 2.0 dBi | |
| Impedance: 50 Ohm nominal | |
| Wi-Fi 11b/g/n and WPS Certified (WPS will be optional) | |
| support | |
| Wireless ON/OFF Switch | support |
| Factory Reset Button | support |
| Consol pin | support |
| TR-068 | support upon request |
| WPS | support |
| Dying Gasp | support upon request |
2. LED Indicators
| LED Indicative | Color | Status | Description | |
| Power | Green | Solid Light | Power on | |
| Light off | Power off | |||
| Red | Solid Light | 1). Device boot POST (Power On Self Test). 2). Device POST failure (not bootable). 3). Device malfunction. | ||
| LAN | Green | Solid Light | Powered device connected to LAN port | |
| Blinking | LAN activity present | |||
| Light off | No Activity | |||
| WLAN 2.4GHZ | Green | Solid Light | Device enable 2.4G WLAN | |
| Blinking | WLAN activity | |||
| Light off | Device disable 2.4G WLAN | |||
| WPS 2.4G | Green | Solid Light | Connection is successfully established between the router and the client, the LED would remain in solid for 5 sec. | |
| Blinking | WPS is successfully triggered | |||
| Light off | Device ready for new WPS setup | |||
| USB | Green | Solid Light | Device connected to USB port | |
| Blinking | Data transmission | |||
| Light off | No Activity | |||
| WAN | Green | Solid Light | The link is established | |
| Blinking | Data transmission | |||
| Light off | The link is not established | |||
| DSL | Green | Solid Light | DSL good sync | |
| Blinking | DSL attempting sync* | |||
| Light off | No carrier signal | |||
| Internet | Green | Solid Light | IP connected and no traffic detected | |
| Blinking | IP connected and Internet traffic detected | |||
| Light off | Modem power off, modem in bridged mode | |||
| Red | Solid Light | Device attempted to become IP connected and failed | ||
3. S/W Features
| Feature Item | Feature | Detailed Description |
| ADSL Compliance | T1.413i2, G.992.1 (G.dmt), G.992.2 (G.lite) | |
Annex A (Annex B and C are optional) | ||
G.992.3 (G.bis/ADSL2) | ADSL and ADSL2 dual mode PHY | |
| G.992.5 (ADSL2+) | ADSL2+ | |
Annex L (Reach Extended ADSL2) | ||
| Annex M | ||
VDSL Compliance
| G.993.2
| Vdsl profiles supported: 8a/b/c/d , 12a/b, 17a |
| US0 | ||
Diagnostics mode/DELT
| ||
Dying GASP
| ||
PhyR
| ||
Virtual Noise
| ||
Both Annex A and Annex B
|
Both Annex A and Annex B band plans
| |
| WIFI Compliance | IEEE 802.11b/g/n | |
| Support 2x2 antennas | ||
| Support 2-stream spatial multiplexing up to 270Mbps | (Can upgrade to 300Mbps) | |
| Support MCS 0-15 and MCS 32 modulation and coding rates | ||
| Support 20M and 40M channels | ||
| Support for STBC in both TX and RX | ||
| Network Protocols and Features | RFC2684 VC-MUX, LLC/SNAP encapsulations for bridged or routed packet | VC-MUX for any connection type |
RFC2364 PPP over
| RFC2364 LLC/NLPID
| |
| AAL5 | encapsulation for PPPoA | |
802.1q/1p VLAN over RFC2684 Bridge encapsulation | 802.1q header insertion toward WAN and de-insertion toward LAN over RFC2684 bridge mode over AAL5. Supports multiple VLANs on multiple PVCs and mapping VLANs, PVCs and physical LAN port to multiple bridges. | |
| PPPoA | Support AUTO, PAP, CHAP, MS- CHAP authentication Added static IP address assignment. | |
| PPPoE | Support AUTO, PAP, CHAP, MS- CHAP authentication Added static IP address assignment. | |
Multiple PPPoE sessions on single PVC | Allows multiple PPPoE sessions on one PVC. | |
| PPPoE pass-through | Supports concurrent PPPoE clients inside the modem and PPPoE clients on the LAN Devices | |
PPPoE - filtering of non-PPPoE packets between WAN and LAN | Previously only filtered non- PPPoE packet from LAN to WAN, now works in both directions. | |
Auto-clean-up remote staled PPP sessions at BRAS | Clean up staled PPP sessions (PPPoE and PPPoA) at ISP BRAS after ADSL link goes down then up or after modem reboots, if scratch pad is enabled on top boot flash. | |
| IPoA | ||
MER (a.k.a IP over Ethernet over AAL5) | ||
WAN to WAN traffic blocking in bridge mode | ||
Second IP address on LAN interface | Only public IP address and no DHCP on second IP address. | |
| ARP | ||
| DNS relay | ||
DNS server fallback in DNS Relay | Launch dnsprobe process when both primary and secondary DNS’s are assigned. Probe primary DNS status and fallback to secondary DNS. When primary DNS is up again, switch back to primary DNS. | |
| DHCP server | ||
| DHCP client | ||
| DHCP Relay | DHCP relay agent for IPoA and MER type of WAN connections. | |
| NAPT | ||
| IGMP Proxy | IGMP v1/v2 | |
| IGMP Snooping | IGMPv1/v2 snooping in bridge mode. Added blocking mode. | |
| RIP v1/v2 | Enable RIP over multiple WAN Interfaces | |
| Dynamic DNS | Automatic update WAN IP address when it is changed to dyndns.org and/or TZO DDNS operator. | |
LAN port to VC mapping | Supports traffic mapping between a group of LAN port to a PVC. | |
Ethernet as WAN interface. | Added Ethernet as WAN interface to support PPPoE or IP over Ethernet. | |
Multiple Protocol VLAN Mux | Support multiple protocols on single PVC using VLAN ID | |
| Multiple Service PVC | Support PPPoE, Bridge, and MER services over a single PVC | |
| Firewall | Stateful Inspection | SPI Fire Wal |
Denial of Service attack | Passed DOS attacks: ARP Attack, Ping Attack, Ping of Death, Land, SYNC, Smurf, Unreachable,Tear Drop | |
TCP/IP/Port/interface filtering rules | Support both incoming and outgoing filtering. | |
| MAC Layer Filtering | Added IGMP in protocol menu. Filter MAC frames based on protocol type, source/destination MAC address, direction | |
Day-time Parental Control | ||
| VPN | IPsec VPN(optional) | Support VPN connection to remote VPN gateway. |
| QoS | IP/Bridge/802.1p QoS | Supported both routed and bridged mode PVCs for packet level QoS: classification rules, priority queuing using ATM TX queues, IP TOS/Precedence, 802.1p marking. Added DiffServ DSCP marking and src/dest MAC addresses classification. |
| Configuration and Management | Web based GUI | |
| Embedded web server | ||
Download image via HTTP or tftp client | ||
Download image via FTP server | ||
Download image via TFTP server | ||
Command Line Interface via serial port, telnet, or ssh | added dumpcfg, sntp commands. Added option to tftp, adsl, wan, ppp commands. Upgrade sshd to version 0.46. | |
Menu-driven CLI via serial port or telnet | Added dump configuration. | |
Universal Plug and Play (UPnP) Internet Gateway Device (IGDv1.0) | V2.14L.02: Upgraded UPnP with latest version. Added support for ADSL IGD. Enable/disable UPnP without reboot. | |
| SNMP v1/v2c agent(optional) | ||
SNMP MIBs: rfc2662 ADSL line MIB, rfc2515 ATM MIB, MIB-II | Support GET only except GET/SET for system MIB and ifAdminStatus in ifTable. | |
Date/time update from SNTP Internet Time Server | Automatic synchronize date and time with Internet Time Servers and local time zone setup. Display Date/time in device info and syslog. Added SNTP command. | |
| Daylight saving zone | ||
| TR-69(optional) | Compliance with Brandband forum standard. |
4.Mechanic & ID Design
4.1Physical & Environment
4.1.1Power
-Input: 100-240VAC, 50/60Hz (Region dependent)
-Output: 12V DC,1.5A (Switch)
-Dying Gasp: Supported
-Power Switch: Push button supported
-Reset Button: Reset to factory default by pushing button
-Wifi Buttom: Push button supported
-WPS Button: Push button supported
4.1.2Operation Temperature
- 0℃ to 45℃
4.1.3Storage Temperature
--4℉ to 149℉ (-20℃ to 70℃)
4.1.4Humidity
-5% ~ 95% non-condensing
