Winan Industrial Limited |
|
1.6MPa Dn65 Ductile Iron Mechanical Gate Valve Water Flange Gate
Industrial Ductile Iron Carbon Steel Non-Vertical Valve Stem DN80 DN150 Water Flange Gate Valve With Pipe Fittings
Gate valve introduction:
Surface of the valve was covered with advanced epoxy and flashboard was covered with rubber. Other parts which will contact with medium are all made of stainless steel or copper alloy, which fundamentally prevent it from being contaminated by medium. It fits pipelines of drinkable water, food industry, fire water and sewage treatment.
Technical Parameters:
Nominal Pressure | 1.0 | 1.6 | Mpa | |
Test Pressure | Shell | 1.5 | 2.4 | |
Seal | 1.1 | 1.76 | ||
Medium Temperature | -15℃-+80℃ | |||
Medium | Water,Air |
DN (mm) | L(mm) | H (mm) | Φ > > (mm) | D | D1 | Z-d | ||||
Short | Long | 1.0 Mpa | 1.6 Mpa | 1.0 Mpa > > | 1.6 Mpa> | 1.0 Mpa > > | 1.6 Mpa | |||
50 | 150 | 250 | 260 | 250 | 165 | 125 | 4-19 | |||
65 | 170 | 270 | 270 | 250 | 185 | 145 | 4-19 | |||
80 | 180 | 280 | 310 | 250 | 200 | 160 | 8-19 | |||
100 | 190 | 300 | 340 | 250 | 220 | 180 | 8-19 | |||
125 | 200 | 325 | 405 | 350 | 225 | 210 | 8-19 | |||
150 | 210 | 350 | 460 | 350 | 285 | 240 | 8-23 | |||
200 | 230 | 400 | 570 | 350 | 340 | 295 | 8-23 | 12-23 | ||
250 | 250 | 450 | 660 | 500 | 395 | 405 | 350 | 355 | 12-23 | 12-28 |
300 | 270 | 500 | 770 | 500 | 445 | 460 | 400 | 410 | 12-23 | 12-28 |
350 | 290 | 550 | 870 | 500 | 505 | 520 | 460 | 470 | 16-23 | 16-28 |
400 | 310 | 600 | 1010 | 640 | 565 | 580 | 515 | 525 | 16-28 | 16-31 |
450 | 330 | 650 | 1080 | 640 | 615 | 640 | 565 | 585 | 20-28 | 16-31 |
500 | 350 | 700 | 1180 | 640 | 670 | 715 | 620 | 650 | 20-28 | 20-34 |
Gate valve characteristics:
Light weight
The body is made of high-grade nodular cast iron, the weight is
about 20%~30% lighter than the traditional gate valve, and the
installation and maintenance are convenient.
Overall encapsulation
The gate adopts high-quality rubber for overall inner and outer
rubber. European rubber vulcanization technology enables the
vulcanized gate to ensure accurate geometric dimensions, and the
rubber and ductile cast gate are firmly connected, not easy to fall
off and have good elastic memory.
Note for gate valve:
1. Handwheels, handles and transmission mechanisms are not allowed
to be used for lifting, and collisions are strictly prohibited.
2. The double gate valve should be installed vertically (that is,
the valve stem is in the vertical position and the handwheel is on
the top).
3. For gate valves with hand wheels or handles, no auxiliary levers
should be added during operation (if the sealing is not tight, the
sealing surface or other parts should be checked and repaired).
Turn the handwheel and handle clockwise to close, otherwise open.
The gate valve with transmission mechanism should be used in
accordance with the product manual.