Guangzhou Huilian Machine Equipment Co., Ltd. |
Verified Suppliers
|
|
Orange Peel Grapple Component:
1, Hydraulic Control System
2, Hydraulic Power System
3, Riveting Welding Strcuture
Main Features
1.Robust structure optimal weight.
2. Maximized Grabbing capacity
3.Full 360 degree hydraulic rotation.
360 Degree Rotation Excavator Hydraulic Orange Peel Grab Steel Scrap Grapple for 24ton 30ton 36ton Excavator
Grab is a lifting appliance which depend on jaw opening and closing
crawl and unloading bulk material.According to be stacked capture
material density is divided into light, medium, heavy, and super
heavy.
Grabs can be manufactured in various executions, each model
accustomed to the material to be handled. For loading and
discharging of scrap, mixed scrap, compacted car bodies, small
rocks, wood chips, etc. The grabs are manufactured of high wear
resistant steel.
Grabs are available with rotator or integrated rotation (heavy
duty) with sturdy slewing, depending on the type.The heavy duty
version features solid end stops, accurate fittings, reinforced
bolts and large bearing surfaces amongst others.
Our Orange Peel Rotary Grapple Product Parameter
Model | Unit | HL06M5L-SX | HL08M5L-SX | HL10M5L-SX | HL12M5L-SX |
Max. opening | mm | 2100 | 2300 | 2500 | 2750 |
Opening height | mm | 1595 | 1800 | 1900 | 1980 |
Opening width | mm | 2320 | 2520 | 2750 | 3000 |
Closing height | mm | 1300 | 1480 | 1550 | 1650 |
Closing width | mm | 1966 | 2150 | 2250 | 2416 |
Max. pressure | Kg/cm² | 260 | 260 | 260 | 260 |
Max.oil flow | L/min | 180-280 | 180-280 | 180-280 | 180-280 |
Capacity | m³ | 0.6 | 0.8 | 1.0 | 1.2 |
Weight | kg | 1200 | 1760 | 1880 | 1980 |
Suitable Excavator | ton | 12-18 | 18-24 | 24-36 | 36-40 |
Hydraulic rotary steel grab product maintenance:
1. Daily checkpoints
Whether there is any damage or deformation of the body, whether
there is leakage of the hose interface, damage to the pin and
bushing and its replacement cycle, check the loosening state of
bolts and nuts, check the oil level and loosing of the gear,
tighten the bolt.
2. Regular checkpoints
The seals and rotating parts of the hydraulic cylinder will wear
out, and should be replaced in time after reaching the service
life. Replacement parts should be matched with the original
factory.
Check the rotation shaft, the rotation shaft unlimited rotation 360
degrees, convenient from any Angle accurate work, check the
rotation shaft has enough lubricant, bolts are tight enough.
3. Check the tightening state of bolts and install new bolts. Check
after 8 hours of use, and ensure that the bolts tightened are not
loose. The damaged bolts should be replaced in time. It should be
replaced after about 1500 hours or 12 months of use after
installation.
4. It is recommended to regularly check whether there is oil
leakage to ensure that there is no fault and the product can run
smoothly.
Every 4 hours: fill lubriCATEEEEing oil, lubriCATEEEEe shaft pin
and rotating gear once. Every six months or 1000 hours (whichever
comes first): replace the hydraulic cylinder oil seal and motor oil
seal once.
Special notes for operation and use of hydraulic rotary steel
grabber:
Only reasonable and correct use of product can effectively improve
work efficiency, but also ensure the service life of the product,
so the following special precautions must be read in detail before
using the steel grabber:
1 Suitable for grabbing uniform bulk material, not suitable for
long boring, otherwise easy to strain .
2.Do not use grapples as levers and do not use grapples to move
heavy objects.
3.It is forbidden to push and pull with grapples or overload grab
heavy objects.
4.When working, try to adjust the grip and excavator arm to keep in
a vertical position, ensure that the force of each grab is even.
5.The tip of the claw is wear-resistant welding wire, which should
be repaired in time during use to prevent damage.
6.The rotation speed can not be adjusted too fast to prevent the
grip from grasping the heavy object ,and while stop the action, due
to the sudden brake, too much inertia caused damage of the motor.
7.After stopping the operation, check the pipeline joints of the
grips in time, check whether the fixing bolts are loose due to
friction and collision caused by long time work. If oil leakage and
bolt looseness are found, tighten them manually , and replace the
hydraulic cylinder and motor oil seals once every six months or
1000 hours (whichever comes first).
About Us
Guangzhou Huilian Machinery Equipment Co., Ltd. is a professional
development, production and sales of hydraulic crushers,quick
couplers, high frequency vibration crushers, hydraulic shears,
hydraulic crushers, stone apples, log grabs and other accessories
for construction machinery.
Hydraulic grapple is widely used for handling, loading and
unloading materials, sugarcane, wood, stone, steel slag, grabbing
,garbage, scrap metal and other special operations, As one of the
leading Excavator attachment manufacturers in China, Huilian has a
full range of grapples suitable for all kinds of brands excavators