Home Companies Chongqing Aorun Industrial Co., Ltd.

Metallic Anti Corrosive Paint Outdoor Mixed Bright Industrial

Active Member

Contact Us

[China]

Address: Building 21, Shangding Enterprise Park, Yubei District, Chongqing, China

Contact name:Gelon

Chongqing Aorun Industrial Co., Ltd.

Metallic Anti Corrosive Paint Outdoor Mixed Bright Industrial

Country/Region	china
City & Province	chongqing chongqing
Categories	Paint & Coatings

Product Details

Factory Outdoor Mixed Paint Bright Industrial Anti-Corrosive Metallic Paint

Quick Detail:

Name	Art resin 9455	Usage	Boat Paint, Building Coating, Marine coatings
Type	BPA	Function	Anti-corrosion, beautiful, anti-yellowing, transparent, non-toxic and harmless

Description:

Excellent cathodic protection,anticorrosive,abrasion resistance property,thick coating property while construction,climate resistance,dry rapidly, less adust when torch cutting and welding, good compatibility with a wide range of upper coatings, high adhesion with steel surface.
After curing, it may be coated with conventional primers and finishes such as epoxy, coal tar epoxy, vinyls, phenolics, urethanes, acrylics & chlorinated rubber.
Mixing ratio: A: B = 2: 1 (weight ratio)
Drying time: surface dry 2h hard dry 24h
Overcoating interval: minimum 24 hours, maximum 7 days

Storage notice:

Storage: this product should be stored in shady, dry, and ventilated warehouse and storage temperature 5-40℃ is appropriate. The shelf life is 12 months at room temperature. If exceeding shelf life, the products shall be tested before using.

Characters:

High build anticorrosive paint
Excellent resistance to sea water penetration resistance and corrosion
Film strong, wear-resistant
Excellent adhesion
Excellent compatibility

Specification:

Items	Units/conditions	Technical Data
Viscosity	Shore-D	80-85
Volume resistivity	25℃/ Ω./ cm	4.3x1015
Surface resistivity	25℃/ Ω.	2.6x1014
Dielectric strength	25℃ KV/MM	25
Coefficient of linear expansion	CM/K	<6.1x10-5
Glass transition temperature	℃	>90
Temperature resistant	℃	-60~120

The above performance data is typical data measured in a laboratory environment

with a temperature of 25°C and a humidity of 70%. It is for customer reference only

Operative method and tips:

1. Working environment: Please keep the plastic container clean. A, B components are strictly according to the weight ratio, accurately weighed, and stirit evenly along the inner wall of the container clockwise until it is used for 3-5 minutes.

2. According to the operating time and amount of glue deployment, to avoid waste. When the temperature is lower than 15 ° C, please pre-heat the A glue to 30 ° C and then adjust the rubber, easy to operate (low temperature, A glue will thicken ); After use must seal the lid,to avoid the product due to moisture absorption scrapped.

3. When the relative humidity is more than 85%, the surface of the cured product can easily absorb the moisture in the air to form a whitemist.Therefore,when the relative humidity is more than 85%, it is not suitable for room temperature curing. It is recommended to use the heating and curing.
4. The lid must be sealed after use to avoid the product being scrapped due to moisture absorption.

NOTE:

1. Cleanses main films, and dry, dry before spraying and dry. (Udo Abrodraping600 # -800 #, dry abrodrad400 # -600 #)
2. The temperatures are more than 30 ° 100, to be more sensitive to the correct size of button to be thinner and with silver powder paint.
3. Sprinkle tools, technology methods, technology methods, technology methods, technology has been expressed. Otherwise the metal paint layer will swim and have weak metal emotions.
4. Hours of time to buy users or more than 25. Otherwise the nearby card between paved layers is not strong.
5. The spraying after each layer will be sprayed after the metallic paint. If there are any dust spots or particles on the surface paint, clean it with a fixed cloth.
More than ASAP from ASAP on ASAP on ASAP for 6K-based paint. If the time is too long it will affect adhesive.

FAQ:

Question: Are you factory or trader?
Reply: Factory. We set R&D, production and sale in a body and can meet any needs of you.
Question: How do we believe you as a reliable supplier?
Reply: We can supply the related certifications and welcome you to visit our factory and company.
Question: Do you offer sample?
Reply: Yes. Tell us the specific requirement, and we give you the solution.
Question: What package of the products?
Reply: Our packaging is 20 L metal bucket or at your choice.

Question: How can I get more knowledge about your factory or your paint?
Reply: You can browse our website or visite our factory. It would be our pleasure to meet you here.

Reply: Click below to send me more questions and I will answer all your questions.
Please Click Here!! >>>>>>

Packaging:

We offer different size of packaging, 5kg buckets and 20kg buckets are normal size. Customized