Active Member
|
[China]
Address: #1008.Junjiang Internatioanl Bldg. 228 Ningguo Rd. Yangpu Dist. Shanghai. 200090. China
Contact name:
Shanghai Korain Biotech Co., Ltd |
|
|
High Precision and Sensitivity S1PR3 Human Sandwich ELISA Kit With
2 Hours Assay Time
Cat.No E6749Hu
Standard Curve Range: 0.05ng/ml - 20ng/ml
Sensitivity: 0.018ng/ml
Size: 96 wells
Intended Use
This sandwich kit is for the accurate quantitative detection of
Human Sphingosine 1 Phosphate Receptor 3 (also known as S1PR3) in
serum, plasma, cell culture supernates, cell lysates, tissue
homogenates.
Precision
Intra-Assay Precision (Precision within an assay) Three samples of
known concentration were tested on one plate to assess intra-assay
precision.
Inter-Assay Precision (Precision between assays) Three samples of
known concentration were tested in separate assays to assess
inter-assay precision.
CV(%) = SD/mean x 100
Intra-Assay: CV<8%
Inter-Assay: CV<10%
*This product is for research use only, not for use in diagnosis
procedures. It’s highly recommend to read this instruction entirely
before use.
Reagent Provided
| Components | Quantity |
| Standard Solution (24ng/ml) | 0.5ml x1 |
| Pre-coated ELISA Plate | 12 * 8 well strips x1 |
| Standard Diluent | 3ml x1 |
| Streptavidin-HRP | 6ml x1 |
| Stop Solution | 6ml x1 |
| Substrate Solution A | 6ml x1 |
| Substrate Solution B | 6ml x1 |
| Wash Buffer Concentrate (25x) | 20ml x1 |
| Biotinylated Human S1PR3 Antibody | 1ml x1 |
| User Instruction | 1 |
| Plate Sealer | 2 pics |
| Zipper bag | 1 pic |
Reagent Preparation
All reagents should be brought to room temperature before use.
Standard Reconstitute the 120μl of the standard (24ng/ml) with 120μl of
standard diluent to generate a 12ng/ml standard stock solution.
Allow the standard to sit for 15 mins with gentle agitation prior
to making dilutions. Prepare duplicate standard points by serially
diluting the standard stock solution (12ng/ml) 1:2 with standard
diluent to produce 6ng/ml, 3ng/ml, 1.5ng/ml and 0.75ng/ml
solutions. Standard diluent serves as the zero standard(0 ng/ml).
Any remaining solution should be frozen at -20°C and used within
one month. Dilution of standard solutions suggested are as follows:
| 12ng/ml | Standard No.5 | 120μl Original Standard + 120μl Standard Diluent |
| 6ng/ml | Standard No.4 | 120μl Standard No.5 + 120μl Standard Diluent |
| 3ng/ml | Standard No.3 | 120μl Standard No.4 + 120μl Standard Diluent |
| 1.5ng/ml | Standard No.2 | 120μl Standard No.3 + 120μl Standard Diluent |
| 0.75ng/ml | Standard No.1 | 120μl Standard No.2 + 120μl Standard Diluent |
| Standard Concentration | Standard No.5 | Standard No.4 | Standard No.3 | Standard No.2 | Standard No.1 |
| 24ng/ml | 12ng/ml | 6ng/ml | 3ng/ml | 1.5ng/ml | 0.75ng/ml |
Wash Buffer Dilute 20ml of Wash Buffer Concentrate 25x into deionized or
distilled water to yield 500 ml of 1x Wash Buffer. If crystals have
formed in the concentrate, mix gently until the crystals have
completely dissolved.
Assay Procedure
1. Prepare all reagents, standard solutions and samples as
instructed. Bring all reagents to room temperature before use. The
assay is performed at room temperature.
2. Determine the number of strips required for the assay. Insert
the strips in the frames for use. The unused strips should be
stored at 2-8°C.
3. Add 50μl standard to standard well. Note: Don’t add antibody to standard well because the standard solution
contains biotinylated antibody.
4. Add 40μl sample to sample wells and then add 10μl anti-S1PR3
antibody to sample wells, then add 50μl streptavidin-HRP to sample
wells and standard wells ( Not blank control well ). Mix well.
Cover the plate with a sealer. Incubate 60 minutes at 37°C.
5. Remove the sealer and wash the plate 5 times with wash buffer.
Soak wells with at least 0.35 ml wash buffer for 30 seconds to 1
minute for each wash. For automated washing, aspirate all wells and
wash 5 times with wash buffer, overfilling wells with wash buffer.
Blot the plate onto paper towels or other absorbent material.
6. Add 50μl substrate solution A to each well and then add 50μl
substrate solution B to each well. Incubate plate covered with a
new sealer for 10 minutes at 37°C in the dark.
7. Add 50μl Stop Solution to each well, the blue color will change
into yellow immediately.
8. Determine the optical density (OD value) of each well
immediately using a microplate reader set to 450 nm within 10
minuets after adding the stop solution.
